Cerber C816 - Page 25

25
While the system is being within “main programming menu” select section [021] to establish the ding options. The 1 to 6 options will be displayed according to the table below:
Key pressed
to toggle
option
KP-126Pz / KP-164Pz (LED keypads)
Description
KP16LCD / KP16LCDL (LCD keypads)
Zone
LED
ON OFF 1
st
line message
2
nd
line message
Enabled Disabled
[1] 1
enabled
*
disabled
Dings upon keyswitch
arming/disarming
KeyswitchDing Enable k1 Disable k1
[2] 2
enabled
*
disabled
Dings upon arming (unless
keyswitch arming)
DingArming minutes k2 hours k2
[3] 3
enabled
*
disabled
Dings upon disarming (unless
keyswitch disarming)
DisarmDing Enable k3 Disable k3
[4] 4
enabled
*
disabled Dings during exit delay
ExitDing Enable k3 Disable k3
[5] 5
enabled
*
disabled
Warning dings during the 3 minutes
before autoarming
AutoarmDing Enable k3 Disable k3
[6] 6
enabled
*
disabled Dings after the exit delay time
AfterExitDing Enable k6 Disable k6
[7] 7
enabled
*
disabled
Warning on keypads’ buzzer when
siren sounds
KpdAlarm Enable k7 Disable k7
[8] 8
*
English Alternate Keypad messages language
KpdsLang English k8 Portug k8
Note: The default programmed options are marked with *.
Press the [1] to [8] keys in order to turn the appropriate option enabled/disabled and the keypads will display activate/deactivate status of the corresponding options.
After setting these options, press [#] key to confirm. The keypad buzzer will sound 6 confirmation beeps and the panel exits the [021] programming section, waiting for a new
command to enter another section or [#] key to exit the main programming menu.
Notes:
1. One ding means the siren will be activated (will sound) for “ding time” defined in section [050];
2. More dings means the siren will sound for “ding time” alternating with “ding pause” defined in section [050].
Section [022]: Time Measurement Unit for PGM output defined as pulse
While the system is being within “main programming menu” select section [022] to establish the Time Measurement Unit for PGM outputs defined as pulse. The 1 to 6 options will be
displayed according to the table below:
Key pressed
to toggle
option
KP-126Pz / KP-164Pz (LED keypads)
Description
KP16LCD / KP16LCDL (LCD keypads)
Zone
LED
ON OFF 1
st
line message
2
nd
line message
Enabled Disabled
[1] 1
minutes
*
seconds PGM1 time measurement unit
TimePGM1 min k1 sec k1
[2] 2
minutes
*
seconds PGM2 time measurement unit
TimePGM2 min k2 sec k2
[3] 3
minutes
*
seconds PGM3 time measurement unit
TimePGM3 min k3 sec k3
[4] 4
minutes
*
seconds PGM4 time measurement unit
TimePGM4 min k4 sec k4
[5] 5
minutes
*
seconds PGM5 time measurement unit
TimePGM5 min k5 sec k5
[6] 6
minutes
*
seconds PGM6 time measurement unit
TimePGM6 min k6 sec k6
Note: The default programmed options are marked with
*
.
Press the [1] to [6] keys in order to turn the appropriate option enabled/disabled and the keypads will display activate/deactivate status of the corresponding options.