Cerber C816 - Section [034] - OPTIONS for voice;sound dialer

36
[3] 3
* enabled disabled
*
Reports tampers, troubles, restores and periodical test
to CS1
TmpTrbTstCS1 Enable k3 Disable k3
[4] 4
* enabled disabled
*
Reports fire and emergency to CS1
FireEmCS1 Enable k4 Disable k4
[5] 5
* enabled disabled
*
Reports alarms, restorations, ambush and panics to CS2
AlResAmbPanCS2 Enable k5 Disable k5
[6] 6
* enabled disabled
*
Reports arming, disarming and bypassing to CS2
ArmDisByssCS2 Enable k6 Disable k6
[7] 7
* enabled disabled
*
Reports tampers, troubles, restores and periodical test
to CS2
TmpTrbTstCS2 Enable k7 Disable k7
[8] 8
* enabled disabled
*
Reports fire and emergency to CS2
FireEmCS2 Enable k8 Disable k8
Note: The default programmed options are marked with *.
Press the [1] to [8] keys in order to turn the appropriate option enabled/disabled and the keypads will display activate/deactivate status of the corresponding options.
After setting these options, press [#] key to confirm. The keypad buzzer will sound 6 confirmation beeps and the panel exits the [33] programming section, waiting for a new
command to enter another section or [#] key to exit the main programming menu.
Notes:
1. The options selected in [033] section are operational only if the option of split reporting is selected in section [032] – OPTIONS for digital communicator.
2. Keeping options in [033] section as default (all events are selected in [033] section to be reported to CS1 and to CS2) and programming 2 phone numbers in sections [074] and [075],
will result in a “double reporting”, to both CS1 and CS2.
Section [034] – OPTIONS for voice/sound dialer
While the system is within “main programming menu”, in order to establish the voice/sound dialer options select [034] section. The 1 to 5 options will be displayed according to the
table below:
Key
pressed to
toggle
option
KP-126Pz / KP-164Pz (LED
keypads)
Description
KP16LCD / KP16LCDL (LCD keypads)
Zone
LED
ON OFF 1
st
line message
2
nd
line message
Enabled Disabled
[1] 1
enabled
*
disabled Follow me report
VsRepAlarms Enable k1 Disable k1
[2] 2
enabled
*
disabled
“AC power loss” event initiates voice/sound reporting
VSRepACloss Enable k2 Disable k2
[3] 3
enabled
*
disabled
Voice/sound dialer answers to the remote
interrogation calls
VSRepAnswer Enable k3 Disable k3
[4] 4
enabled
*
disabled Ambush event initiates the sound/voice reporting
VSRepAmbush Enable k4 Disable k4
[5] 5
enabled
*
disabled Voice module
MPV Enable k5 Disable k5
[6]
6
enabled
*
disabled Battery trouble reported to “follow-me” numbers
VSBattTbl Enable k6 Disable k6
Note: The default programmed options are marked with *.
Press the [1] to [6] keys in order to turn the appropriate option enabled/disabled and the keypads will display activate/deactivate status of the corresponding options.
After setting these options, press [#] key to confirm. The keypad buzzer will sound 6 confirmation beeps and the panel exits the [034] programming section, waiting for a new
command to enter another section or [#] key to exit the main programming menu.
Notes:
1. If first option in this section is set as enabled, then, upon occurring in the system of some alarm events, the control panel will automatic initiate the reporting on the phone line of
these events and the system status, too, by voice messages or by synthesis sounds, specific to these events.