23
harnesses by pressing the red button (Fig. 18),
and pull the harnesses in an outward direction
(Fig. 19A).
Fit the buckle straps in the relevant slots
located on the sides in the cover (Fig. 19B);
this makes it easier to position your child.
Positioning the child in the child car seat.
WARNING! Always make sure that your child is
seated with his back resting against the back-
rest of the child car seat and with the crotch
strap positioned correctly.
Position the crotch strap correctly, take the
straps and join the two buckle straps. (Fig. 20).
Push them together rmly inside the buckle
until you hear a loud click (Fig. 21). In order
to ensure safety, the two buckle straps are
designed to prevent either from being released
one at a time.
To tension the safety harness of the child car
seat, pull the adjustment strap (Q) (Fig. 22) of
the harness, until the harness straps adhere to
the child’s body correctly.
WARNING! Do not over-tighten the harnesses
around the child: if you can insert one nger
between the harness and your child’s shoul-
ders, it means that they are tightened correctly.
WARNING! Check that the harness is not
twisted.
WARNING To turn the child car seat facing
forward, use the release lever (E) and position
the car seat in forward-facing position until
you hear the CLICK when it is fastened cor-
rectly (Fig. 23).
7. ADJUSTING THE HEADREST AND HAR-
NESSES
The height of the headrest and restraint har-
nesses can be simultaneously adjusted to 8
positions by using the headrest adjustment
ring (F).
WARNING! To adjust them correctly, the
headrest must be tted so as to allow that
the harnesses come out from the backrest at
the height of the child’s shoulders (Fig. 24). To
adjust the height, pull the adjustment ring (F)
located above the headrest (Fig. 25) up until
the desired position is reached; now release
the ring and ease the headrest until a click
is heard, indicating that it is locked correctly
into position.
To tension the safety harness of the child car
seat, pull the adjustment strap (E) (Fig. 26) of
the harness, until the harness straps adhere to
the child’s body correctly.
WARNING! Do not over-tighten the harnesses
around the child: If you can insert one nger
between the harness and your child’s shoul-
ders, it means that it is tightened correctly.
8. ADJUSTING THE INCLINATION OF THE
CHILD CAR SEAT
The child car seat can be reclined to 4 positions.
To adjust the inclination of the child car seat,
pull the reclining lever (J) (Fig. 27).
To make reclining as easy as possible, we rec-
ommend doing so with the child car seat in
an intermediate position.
9. INSTALLING THE SIDE SAFETY SYSTEM
The Side Safety System is a device that is in-
stalled on the door side for utmost protection
in the case of a side impact.
To install it, insert the end in the hole in the
structure, press the central portion and rotate
it (Fig.28).
10. BUILT-IN MIRROR
The car child seat is equipped with a mirror
that allows you to check the position of the
child while driving; it is possible to adjust the
inclination of the mirror by acting on it with a
light pressure (Fig. 29)
11. MAINTENANCE
The cleaning and maintenance of the product
must only be carried out by an adult.
How to clean the fabric cover.
The child car seat’s fabric cover can be removed
and cleaned by hand or in a washing machine
at 30°C. Please refer to the care label for instruc-
tions on cleaning the seat fabric.
Machine washable at 30°C.
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
Never use abrasive detergents or solvents. Do
not dry the fabric cover within a dryer, let it dry
without squeezing it.
The fabric cover must only be replaced with
another cover approved by the manufacturer,
since it is an integral part of the child Car seat
and, therefore, one of its safety elements.
WARNING! To ensure the safety of the child
car seat, never use it without its fabric cover.
Now remove the cover following the instruc-
tions below:
Press the restrain harnesses adjustment but-
ton and, at the same time, hold the two har-
nesses of the child car seat, located under the
shoulder straps, and pull in your direction to
loosen them;
Unfasten the safety harness, pressing the red
button on the buckle;
Remove the cover starting from the two hooks
under the seat near the reclining button (Fig. 30);
Release the press-studs in the centre of the
backrest and pull out the ends inserted in the
relevant slots of the child car seat (Fig. 31).
To complete removal, remove the headrest
from above (Fig. 32); complete removal by
pulling out the lower part of ap (Fig. 33)
How to clean the plastic or metal parts
Clean the plastic and coated metal parts with a
damp cloth only. Never use abrasive detergents
or solvents.
The moving parts of the child Car seat must
not be lubricated.
CHECKING THE CONDITION OF THE COM-
PONENTS
It is recommended to regularly check the con-
dition of the following components to make
sure they are not damaged or worn:
• fabric cover: check that the padding does
not come out from the seams. Check the
condition of the seams: they must always be
intact and undamaged.
• belts: check that the fabric lining is not frayed
30° C
To Next Page
Loading...
