E1
SAFETY PRECAUTIONS
INST.No.DB6-61-6
Digital Indicating Controller
DB600
Instruction Manual
for Installation
Thank you for purchasing the DB600.
Before operating the product described in this user’s manual, please
take note of the following points regarding safety.
Be sure to keep this manual nearby for handy reference.
Please read the "Terms and Conditions" from the following URL
before ordering or use:
https://www.chino.co.jp/support/guarantee/index.html
NOTICE
Be sure that the user receives this manual before the product is
used. Copying or duplicating the manual in part or in whole is
forbidden.
The information and specifications in the manual are subject to
change without notice.
Considerable effort has been made to ensure that this manual is free
from inaccuracies and omissions. If you should find an error or omission,
please contact your nearest CHINO office.
In no event is CHINO liable to anyone for any indirect, special or
consequential damages as a result of using this product.
This manual only explains the handling precautions, mounting,
wiring, input type, list of parameters and main specifications.
For instruction manual other than this document, go to CHINO
homepage https://www.chino.co.jp, register for a membership, and
download. See DB600 or DB60Z Instruction manual (General) for
the detail handling procedures etc.
Unpacking
Check the following items when removing the DB600 from its package:
Name Q'ty Remarks
Mounting Bracket 2pcs
Instruction Manual
(installation)
1 This Manual
A protective film is attached to the front console of this unit to protect the
surface. After installation and wiring are complete, peel off the film
before use.
The use of this product in a manner not specified by the manufacturer
will impair its built-in safety features.
WARNING
CAUTION
Quick Start Guide
From installation to Input type and SV setup
Step 1. Mount ......................... Page E2
Step 2. Wire ............................ Page E3
Step 3. Set Input type .......... Page E5
Step 4. Set the SV ................. Page E5
Part names and functions
(1) Measured value (PV)/ Parameter setting title
Displays measured value (PV) or parameter setting screen title.
(2)
Setting value (SV)/ operating condition/ parameter setting value
Displays setting values (SV) or other parameter values.
(3)
Cursor for setting parameter
Displays cursor by pressing [>] key when the parameter is
switchable digits during parameter setting screen is displayed.
(4)
Analog bar
Displays measured value (PV) or analog bar of parameter by
setting of bar display.
(5) Output
Displays output status.
(6) Event
Displays event status of event 1 to 4.
(7) Operating condition display
Displays operating condition.
(8) Setting value ramp display
Displays the ramp status of setting value.
(9)
Pattern No. (program operation ON)
*with program function specifications
The pattern No. being executed or being set will be lit.
(10) Execution No./ step No./ Group No./Event No.
The execution No. or step No. or group No. or event No. being
executed or being set will be lit.
(11) Operation screen display
SV: Lights while displaying [PV/SV] of operation screen.
OUT: Lights while displaying [PV/OUT1] of operation screen.
OUT2: Lights while displaying [PV/OUT2] of operation screen.
*with output 2 specifications
(12)
Communication status display
*with communication interface specifications
Communication display (MODEa) is ON
S (SEND): Blinks while sending communication command.
R (RECEIVE): Blinks while receiving communication command.
*Communication status of engineering port is not displayed.
Step 1. Mounting
Location
Install the controller in a location that meets the following criteria:
(Environment)
• Indoor use
• Away from direct sunlight.
• Away from high temperatures.
• Where there are no vibrations and shocks.
• Away from liquids (water etc.).
• Away from condensation.
• Industrial environment
(Overvoltage category: II, Transient overvoltage: 2500V, Pollution
degree: 2)
WARNING
(1)Before supplying the power to the product, check that the wiring is
correct and power supply voltage matches with the rated voltage
etc.
(2)This product does not have a power supply switch. Install a circuit
breaker that matches the rating specifications in the power supply
of the product.
(3)To prevent electric shock, provide the terminal of the product with
safety measures such that the user will not be able to touch the
final product directly.
(4)
This product is designed as a general-purpose product for general
industrial products. It is not intended for use in human-life and
property related applications such as nuclear and radiation related
equipment, medical equipment, aerospace equipment, railroad, and
marine transportation equipment. To use this product for equipment
that requires high quality and safety that affects human-life and
property, design and install the protection and safety circuits to
ensure safety at your own responsibility.
(5)Do not put your hand and tool inside the product. You may get an
injury or an electric shock.
WARNING
(6)If there is offensive smell, strange noise or smoke or if the
temperature increases abnormally, it is very risky hence cut off the
power supply immediately and contact the dealer or nearest
CHINO's office.
(7)If repairing or remodeling is necessary, contact the dealer or
nearest CHINO's office. Only the service engineers appointed by
our company will change the parts, do the repairing and
remodelin
.
(8)In order to use the product correctly and safely, follow this
instruction manual. Please understand beforehand that our
company will not at all be responsible for any claims for injury,
damage, and passive damage due to wrong use of the product.
(7)
(8)
(10)
(11)
(4)
(2)
(3)
(1)
(6) (12)
(7)
(4)
Warnings are indicated when mishandling
this product might result in death or
serious injury to the user.
Cautions are indicated when mishandling
this product might result in minor injury to
the user, or only physical damage to this
product.
(3)
(11)
(2)
(1)
(6)
(12)
(5)
(9)
(10)
(1)
(2)
(6)
(3)
(4) (12)
(5)
(9)
(10)
(7)
(8)
(9)
(8)
(5)
(8)
(11)
To Next Page
Loading...
