EasyManuals Logo

Chord Hugo Quick Start Manual

Chord Hugo
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Connecting your source to M Scaler 2.0
Connecting M Scaler to DAVE, TT 2 or Qutest 3.0
Connecting M Scaler to a third-party DAC 4.0
In order for M Scaler to upscale/upsample your music, you must
connect your source to any input of M Scaler. You can connect multiple
sources if you wish. If you are using a MAC/Linux device you will not
need a driver but a Windows device will need a driver from the M scaler
section of our website:
chordelectronics.co.uk/product/hugo-mscaler/
To experience the full 768kHz upsampling benefits of M Scaler, you
must connect it in dual-data mode to a Chord Electronics DAC using
two BNC cables. These have been provided.
Plug BNC OUT 1 into BNC IN 1 and BNC OUT 2 into BNC IN 2. If you
only plug one BNC cable into the device you will only experience a
maximum upsampling of 384kHz. You no longer require your source to
be connected to your DAC.
OPT OUT
OPT OUT
S/PDIF
S/PDIF
DUAL BNC OUT
DUAL BNC OUT
Input
OPT OUT
OPT OUT
S/PDIF
S/PDIF
DUAL BNC OUT
DUAL BNC OUT
Output
OPT OUT
OPT OUT
S/PDIF
S/PDIF
DUAL BNC OUT
DUAL BNC OUT
Output
Chord Electronics
Hugo M Scaler | Quickstart Manual
The Pumphouse, Farleigh Lane, East Farleigh, Kent, ME16 9NB, United Kingdom
info@chordelectronics.co.uk
chordelectronics.co.uk
Quickstart Manual
Introduction 1.0
Welcome to the M Scaler Quickstart Guide. This shortened guide is
supplementary to the main manual which should be referred to for full
safety and operational information.
Please note, more information on any of these topics is listed within
the full manual.
Warranty 1.1
The M scaler comes with a comprehensive 3-year warranty. To activate
this warranty, please register your device via the Chord Electronics
website:
chordelectronics.co.uk/register-product
Note: please do not use a third-party charger with the M Scaler as it
voids the warranty
For more in-depth information on the safety and warranty of the Hugo M
Scaler, please see section 1 and 2 of the manual.
Connecting M Scaler to a third-party DAC without a supported dual
data mode (x2 parallel BNC inputs) will yield maximum upsampling of
384kHz. We recommend connecting M Scaler to your DAC via BNC/
SPDIF for the maximum upsampling of 384kHz in this configuration.
Connect any output of M Scaler to the input of your DAC. You no
longer require your source to be connected to your DAC.

Other manuals for Chord Hugo

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Chord Hugo and is the answer not in the manual?

Chord Hugo Specifications

Inputs IconInputs
optical TOSLink input capability24-bit/192kHz
RCA coaxial input capability24-bit/384kHz
driverless USB input capability16-bit/44/48kHz
HD USB input capability32-bit/384KHz and DSD128
Bluetooth input capability16-bit/44/48kHz, up to 5m range
Outputs IconOutputs
headphone output jacks2 x 3.5mm
large headphone jack1 x 6.35mm (1 inch)
stereo RCA phono output1 pair
Weight and Dimensions IconWeight and Dimensions
width100mm
height20mm
depth132mm
weight0.4Kg
packed weight0.9Kg

Related product manuals