EasyManuals Logo

Cisco 2901 User Manual

Cisco 2901
408 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #121 background imageLoading...
Page #121 background image
113
Cisco 3900 Series, Cisco 2900 Series, and Cisco 1900 Series Integrated Services Routers Generation 2 Software Configuration Guide
Chapter Configuring Backup Data Lines and Remote Management
Configuring Dial Backup and Remote Management Through the Console Port or Auxiliary Port
Example
The following configuration example specifies an IP address for the ATM interface through PPP and
IP Control Protocol (IPCP) address negotiation and specifies dial backup over the console port.
!
ip name-server 192.168.28.12
ip dhcp excluded-address 192.168.1.1
!
ip dhcp pool 1
import all
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
!
! Need to use your own correct ISP phone number.
modemcap entry MY-USER_MODEM:MSC=&F1S0=1
chat-script Dialout ABORT ERROR ABORT BUSY ““ “AT” OK “ATDT 5555102\T”
TIMEOUT 45 CONNECT \c
!
!
!
!
interface vlan 1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip tcp adjust-mss 1452
hold-queue 100 out
!
! Dial backup and remote management physical interface.
interface Async1
no ip address
encapsulation ppp
dialer in-band
dialer pool-member 3
async default routing
async dynamic routing
async mode dedicated
ppp authentication pap callin
!
interface ATM0
mtu 1492
no ip address
no atm ilmi-keepalive
pvc 0/35
pppoe-client dial-pool-number 1
Step 17
line [aux | console | tty | vty] line-number
[ending-line-number]
Example:
Router(config)# line aux 0
Router(config)#
Enters configuration mode for the
auxiliary interface.
Step 18
flowcontrol {none | software [lock] [in | out] | hardware
[in | out]}
Example:
Router(config)# flowcontrol hardware
Router(config)#
Enables hardware signal flow control.
Command Purpose

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 2901 and is the answer not in the manual?

Cisco 2901 Specifications

General IconGeneral
Operating altitude0 - 3000 m
Non-operating altitude0 - 4570 m
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)0 - 40 °C
Storage relative humidity (H-H)5 - 95 %
Operating relative humidity (H-H)10 - 85 %
Ethernet LANYes
Cabling technology10/100/1000BASE-T(X)
Networking standardsIEEE 802.1Q, IEEE 802.1ag, IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3ah
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet interface typeGigabit Ethernet
DHCP client-
Routing protocolsBGP, EIGRP, OSPF
Supported protocolsIPv4, IPv6, IS-IS, IGMPv3, PIM SM, SSM, DVMRP, IPSec, GRE, BVD, MPLS, L2TPv3, PPP, MLPPP, MLFR, HDLC, RS-232, RS-449, X.21, V.35, EIA-530, PPPoE, ATM
USB version2.0
RS-232 ports1
Expansion slots4 x EHWIC 2 x DSP 1 x ISM
Ethernet LAN (RJ-45) ports2
Firewall securityCisco IOS
Input current1.5 A
AC input voltage100 - 240 V
Power source typeAC
AC input frequency47 - 63 Hz
Power consumption (typical)40 W
Product colorBlack
Rack capacity1U
SafetyUL 60950-1, CAN/CSA C22.2 No. 60950-1, EN 60950-1, AS/NZS 60950-1, IEC 60950-1
Flash memory256 MB
Internal memory512 MB
Electromagnetic compatibility47 CFR, ICES-003, EN55022, CISPR22, AS/NZS 3548, VCCI V-3, EN 300-386, EN 61000, EN 55024, CISPR 24EN50082-1
Weight and Dimensions IconWeight and Dimensions
Depth439.4 mm
Width438.2 mm
Height44.5 mm
Weight6100 g

Related product manuals