Cisco 2921 User Manual

C-15
Cisco 3900 Series, Cisco 2900 Series, and Cisco 1900 Series Integrated Services Routers Generation 2 Software Configuration Guide
Appendix C Using ROM Monitor
How to Use the ROM Monitor—Typical Tasks
id name
flash: compact flash
bootflash: boot flash
usbflash0: usbflash0
usbflash1: usbflash1
eprom: eprom
Modifying the I/O Memory (iomemset)
This section describes how to modify the I/O memory by using the memory-size iomemset command.
Note Use the iomemset command only when it is necessary to temporarily set the I/O memory from the ROM
monitor mode. Using this command improperly can adversely affect the functioning of the router.
The Cisco IOS software can override the I/O memory percentage if the memory-size iomem command
is set in the NVRAM configuration. If the Cisco IOS command is present in the NVRAM configuration,
the I/O memory percentage set in the ROM monitor with the iomemset command is used only the first
time the router is booted up. Subsequent reloads use the I/O memory percentage set by using the
memory-size iomem command that is saved in the NVRAM configuration.
If you need to set the router I/O memory permanently by using a manual method, use the memory-size
iomem Cisco IOS command. If you set the I/O memory from the Cisco IOS software, you must restart
the router for I/O memory to be set properly.
When the configured I/O memory exceeds the IOS limit (1G), IOS will automatically set an appropriate
I/O memory size and print this message: IOMEM size calculated is greater than maximum allowed
during boot up.
SUMMARY STEPS
1. iomemset i/o-memory percentage
DETAILED STEPS
Command or Action Purpose
Step 1
iomemset i/o-memory percentage
Example:
rommon> iomemset 15
Reallocates the percentage of DRAM used for I/O memory
and processor memory.

Cisco 2921 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.1Q, IEEE 802.1ag, IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3u
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
Product color	Black
Rack capacity	2U
USB version	2.0
RS-232 ports	1
USB ports quantity	2
Ethernet LAN (RJ-45) ports	3
DHCP client	-
Routing protocols	BGP, EIGRP, OSPF
Supported protocols	IPv4, IPv6, IS-IS, IGMPv3, PIM SM, SSM, DVMRP, IPSec, GRE, BVD, MPLS, L2TPv3, PPP, MLPPP, MLFR, HDLC, RS-232, RS-449, X.21, V.35, EIA-530, PPPoE, ATM
Firewall security	Cisco IOS
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4570 m
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	10 - 85 %
AC input voltage	100 - 240 V
Power source type	AC
AC input frequency	47 - 63 Hz
Safety	UL 60950-1, CAN/CSA C22.2 No. 60950-1, EN 60950-1, AS/NZS 60950-1, IEC 60950-1
Electromagnetic compatibility	47 CFR, ICES-003, EN55022, CISPR22, AS/NZS 3548, VCCI V-3, EN 300-386, EN 61000, EN 55024, CISPR 24EN50082-1

Weight and Dimensions

Depth	469.9 mm
Width	438.2 mm
Height	88.9 mm
Weight	13200 g