Cisco AIR-AP1041N-A-K9 - Maximum Transmit Power; 2.4 GHz Power Settings; 5 GHz Power Settings; System and Power Specifications

Data Sheet
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information. Page 4 of 6
Item Specification
-78 dBm @ MCS11
-75 dBm @ MCS12
-71 dBm @ MCS13
-69 dBm @ MCS14
-68 dBm @ MCS15
-74 dBm @ MCS11
-71 dBm @ MCS12
-67 dBm @ MCS13
-65 dBm @ MCS14
-64 dBm @ MCS15
-81 dBm @ MCS11
-78 dBm @ MCS12
-73 dBm @ MCS13
-72 dBm @ MCS14
-70 dBm @ MCS15
-74 dBm @ MCS11
-74 dBm @ MCS12
-69 dBm @ MCS13
-67 dBm @ MCS14
-66 dBm @ MCS15
Maximum Transmit
Power
2.4GHz
●
802.11b
◦
20 dBm with one antenna
●
802.11g
◦
20 dBm with two antenna
●
802.11n (HT20)
◦
20 dBm with two antennas
◦
5GHz
●
802.11a
◦
20 dBm with two antennas
●
802.11n non-HT duplicate mode
◦
20 dBm with two antennas
●
802.11n (HT20)
◦
20 dBm with two antennas
●
802.11n (HT40)
◦
20 dBm with two antennas
Note: The maximum power setting will vary by channel and according to individual country regulations. Refer to the product documentation for specific
details.
Available Transmit
Power Settings
2.4GHz
20 dBm (100 mW)
17 dBm (50 mW)
14 dBm (25 mW)
11 dBm (12.5 mW)
8 dBm (6.25 mW)
5 dBm (3.13 mW)
2 dBm (1.56 mW)
-1 dBm (0.78 mW)
5GHz
20 dBm (100 mW)
17 dBm (50 mW)
14 dBm (25 mW)
11 dBm (12.5 mW)
8 dBm (6.25 mW)
5 dBm (3.13 mW)
2 dBm (1.56 mW)
-1 dBm (0.78 mW)
Note: The maximum power setting will vary by channel and according to individual country regulations. Refer to the product documentation for specific
details.
Integrated Antenna
●
2.4 GHz, gain 4.0 dBi, horizontal beamwidth 360°
●
5 GHz, gain 3.0 dBi, horizontal beamwidth 360°
Interfaces
●
10/100/1000BASE-T autosensing (RJ-45)
●
Management console port (RJ-45)
Indicators
●
Status LED indicates boot loader status, association status, operating status, boot loader warnings, boot loader errors
Dimensions
(W x L x H)
●
Access point (without mounting bracket): 8.7 x 8.7 x 1.84 in. (22.1 x 22.1 x 4.7 cm)
Weight
●
2.3 lbs (1.04 kg)
Environmental
●
Nonoperating (storage) temperature: -22 to 185°F (-3 0 to 85°C)
●
Operating temperature: 32 to104°F (0 to 40°C)
●
Operating humidity: 10 to 90% percent (noncondensing)
System Memory
●
128 MB DRAM
●
32 MB flash
Input Power
Requirements
●
AP1040: 44 to 57 VDC
●
Power Supply and Power Injector: 100 to 240 VAC; 50 to 60 Hz
Powering Options
●
802.3af Ethernet Switch
●
Cisco AP1040 Power Injectors (AIR-PWRINJ4=)
●
Cisco AP1040 Local Power Supply (AIR-PWR-B=)
Power Draw
●
AP1040: 12.95 W
Note: When deployed using PoE, the power drawn from the power sourcing equipment will be higher by some amount
dependent on the length of the interconnecting cable. This additional power may be as high as 2.45W, bringing the total
system power draw (access point + cabling) to 15.4W.
Warranty Limited Lifetime Hardware Warranty