Cisco Catalyst 2960-X Getting Started Guide

If the port LEDs do not turn green after about 30 seconds, make sure that:Note
•
You connected the Ethernet cable to one of the downlink switch ports (not to the console
port).
•
You are using an undamaged Category 5 or 6 Ethernet cable.
•
The other device is on.
Step 7
Start a browser session on the PC, and enter the IP address https://10.0.0.1. When prompted, enter the default password,
cisco.
The switch ignores text in the username
field.
Note
The Express Setup window appears. If the Express Setup window does not appear, make sure that any pop-up blockers or
proxy settings on your browser are disabled and that any wireless client is disabled on your PC or laptop.
Step 8
Enter this information in the Network Settings fields:
All entries must be in English
letters.
Note
•
In the Management Interface (VLAN ID) field, the default is 1. We recommend that you use the default VLAN value.
During Express Setup, VLAN 1 is the only VLAN on the switch. Enter a new VLAN ID only if you want to change
the management interface through which you manage the switch. The VLAN ID range is 1 to 1001.
•
In the IP Address field, enter the switch IP address.
•
In the Subnet Mask field, click the drop-down arrow, and select a subnet mask.
•
In the Default Gateway field, enter the IP address for the default gateway (router).
•
In the Switch Password field, enter your password . The password can be from 2 to 25 alphanumeric characters, can
start with a number, is case sensitive, allows embedded spaces, but does not allow spaces at the beginning or end.
In the Confirm Switch Password field, enter your password again.
You must change the password from the default password,
cisco.
Note
(Optional) Enter this information in the Ethernet Management Port Settings fields:
•
In the IP Address field, enter the IP address of the Ethernet management port.
•
In the Subnet Mask field, click the drop-down arrow, and select an IP Subnet Mask field, click the drop-down arrow,
and select and IP Subnet Mask.
Step 9
Enter information in the optional fields.
You can enter other administrative settings in the Express Setup window. For example, the optional administrative settings
identify and synchronize the switch for enhanced management. The switch clock is automatically synchronized with the
network clock by using NTP. You can manually set the system clock settings if the switch should have different time
settings.
Step 10
Click Submit to save your changes and to complete the initial setup.
After you click Submit:
•
The switch is configured and exits Express Setup mode.
6

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g