Cisco RV042G User Manual

10 RV0xx Series Routers Quick Start Guide
STEP 3 In the address bar, enter the default IP address of the router:
192.168.1.1
STEP 4 When the login page appears, enter the default user name admin
and the default password admin (lowercase).
STEP 5 Click Login. The System Summary page appears.
The router’s default settings are sufficient for many small
businesses. Your Internet Service Provider may require additional
settings. On the System Summary page, check the WAN Status to
see if the router was able to receive an IP Address. If not, continue
to the next step.
STEP 6 To use the setup wizard to configure your Internet connection, click
Setup Wizard on the System Summary page, or click Wizard in
the navigation tree. In the Basic Setup section, click Launch Now.
Follow the on-screen instructions.
If your web browser displays a warning message about the pop-
up window, allow the blocked content.
STEP 7 To configure other settings, use the links in the navigation tree.
Cisco strongly recommends setting a strong administrator
password to prevent unauthorized access to your router. For more
information about all settings, refer to the online Help and the Cisco
Small Business RV0xx Series VPN Router Administration Guide.
Troubleshooting Tips
If you have trouble connecting to the Internet or the web-based
configuration utility:
• Verify that your web browser is not set to Work Offline.
• Check the Local Area Connection settings for your Ethernet adapter.
The PC needs to obtain an IP address through DHCP. Alternatively, it can
have a static IP address in the 192.168.1.x range with the default
gateway set to 192.168.1.1 (the router’s default IP address).
• Verify that you entered the correct settings in the Wizard to set up your
Internet connection, including the username and password if required.
• Try resetting the modem and the router by powering off both devices.
Next, power on the modem and let it sit idle for about 2 minutes. Then
power on the router. You should now receive a WAN IP address.
• Check the DHCP IP address range of your modem. If the modem uses
the 192.168.1.x range, disconnect the cable from the modem to the
router, and then launch the router configuration utility. In the navigation
tree, choose Setup > Network. Enter a new Device IP Address, such as

Cisco RV042G Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3az, IEEE 802.3u
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
Ethernet LAN (RJ-45) ports	6
Routing protocols	IP, RIP-1, RIP-2
Supported network protocols	PPTP, L2TP, IPSec, PPPoE, DHCP
VPN support	PPTP, Layer 2 Tunneling Protocol (L2TP), IPsec, Dead peer detection (DPD), Internet Key Exchange (IKE), split DNS, VPN backup
Firewall security	Stateful packet inspection (SPI) firewall
Security algorithms	3DES, 128-bit AES, 192-bit AES, 256-bit AES, DES, HTTPS, IPSEC
VPN tunnels quantity	50
Authentication method	SHA-1, MD5
MAC address filtering	-
Certification	FCC Class B, CE Class B, UL, cUL, CB
Input current	1 A
Output voltage	12 V
Storage temperature (T-T)	0 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 85 %
Product color	Black
Rack mounting	No

Weight and Dimensions

Depth	200 mm
Width	130 mm
Height	38.5 mm
Weight	600 g