Cisco WS-SUP720-3B - Supervisor Engine 720 - Page 62

98 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

3-18

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

OL-10100-11

Chapter 3 Installing and Configuring Route Switch Processors and Supervisor Engines

Configuring a Supervisor Engine or Route Switch Processor

Table of Contents

Default Chapter3
- Default Chapter3
- Document History8
Document Organization8
Document Conventions9
- Warning Definition9
Related Documentation10
Obtaining Documentation, Obtaining Support, and Security Guidelines10
Chapter 1 Cisco 7600 Product Overview11
- Cisco 7600 Series Routers11
  - Supported Hardware12
  - Features13
Table13
- Cisco 7600 Series Routers13
- Port Addresses16
  - Physical Interface Addresses16
  - MAC Addresses17
- Supervisor Engine 2T18
Chapter 2 Route Switch Processors and Supervisor Engines19
- C H a P T E R 2 Route Switch Processors and Supervisor Engines20
- Overview20
- Route Switch Processor 72027
- RSP720 with 10GE Uplink Ports28
- Supervisor Engine 2T33
  - Primary Supervisor Engine 2T Components35
- Supervisor Engine 720 and Supervisor Engine 3239
  - Front-Panel Controls (RSP720, RSP720-10GE, Sup720, Sup32)39
  - Front-Panel Leds (RSP720, RSP720-10GE, Sup720, Sup32)40
- Supervisor Engine 241
CHAPTER 3 Installing and Configuring Route Switch Processors and Supervisor Engines45
- Preparing for Installation or Removal45
Preparing for Installation or Removal46
Determining Module Location47
- Tools Required for Module Installation47
Installing a Supervisor Engine or Route Switch Processor48
Removing a Supervisor Engine or Route Switch Processor51
Hot Swapping (OIR) Modules52
- Removing and Replacing Memory52
Connecting to the Console Port53
- Connecting a Terminal53
- Connecting a Modem54
Connecting to the Uplink Ports54
Using Flash Memory Cards56
- Installing a Flash Memory Card57
- Removing a Flash Memory Card58
Power Management and Environmental Monitoring58
Determining Software Feature Support58
Upgrading Dimms on RSP72058
Configuring a Supervisor Engine or Route Switch Processor61
Chapter 4 Troubleshooting Route Switch Processors and Supervisor Engines63
- Getting Started63
- AC and DC Power Supply Information63
- Chassis and Supervisor Slot Installation64
Appendix73
Technical Specifications73
- Module Specifications73
- Regulatory Standards Compliance73
- Appendix A Technical Specification74
  - Regulatory Standards Compliance74
Appendix75
Cable and Connector Specifications75
- A P P E N D I X B Cable and Connector Specifications76
- Supported Dense Wave Division Multiplexing (DWDM) Wavelength Optics76
- Supported Coarse Wave Division Multiplexing (CWDM) Wavelength Optics78
- Limiting Connection Distances79
  - Uplink Port Transceiver Modules79
    - 1GE Uplink Ports and Cabling Specifications80
Uplink Port Transceiver Modules80
- 10GE Uplink Ports and Cabling Specifications82
- GBIC Module Cabling Specifications83
- Console Port Cabling Specifications and Pinouts84
- RJ-45 Connector88
- Fiber-Optic Connectors90
LX/LH GBIC and MMF Cable Considerations93
- Patch Cord93
  - Patch Cord Configuration Example93
  - Patch Cord Installation94

Related product manuals

Preview: Cisco WS-C2960-24LC-S

Cisco WS-C2960-24LC-S

Preview: Cisco WS-C4507R

Cisco WS-C4507R

Preview: Cisco WRVS4400N

Cisco WRVS4400N

Cisco Linksys WET11

Preview: Cisco Linksys WET610N

Cisco Linksys WET610N

Preview: Cisco Linksys WRT54GS

Cisco Linksys WRT54GS

Preview: Cisco Linksys WRT610N

Cisco Linksys WRT610N

Preview: Cisco Linksys WRT300N

Cisco Linksys WRT300N

Preview: Cisco Linksys WRT600N

Cisco Linksys WRT600N

Preview: RV042 - Small Business Dual WAN VPN Router

RV042 - Small Business Dual WAN VPN Router