Why is my Clack Control Unit timer displaying the wrong time?
If the Clack Control Unit timer isn't displaying the correct time of day, it might be due to a switched outlet. To resolve this, ensure you are using an uninterrupted outlet. It could also be caused by a power outage, in which case you should reset the time of day. In some cases, a defective PC board can be the reason, and the solution is to replace it.
How to fix Clack Control Unit timer not displaying time of day?
If the Clack Control Unit timer isn't displaying the time of day, first, ensure the AC adapter is properly connected to a power source. If it is, check that the outlet has electric power; repair the outlet or try a different one if necessary. If the problem persists, the AC adapter may be defective and need replacement. As a last resort, the PC board could be defective, requiring replacement.
Why does my Clack Control Unit valve regenerate at the wrong time?
If the Clack Control Unit valve regenerates at the wrong time, it could be due to several reasons. Power outages can cause this, so reset the control valve to the correct time of day. Also, the time of day might not be set correctly, so ensure you reset it. Finally, the regeneration time itself might be incorrect, requiring you to reset it to the proper time.
What to do if Clack Water Specialist WS1TC valve doesn't regenerate when pressing UP and DOWN buttons?
If your Clack Control Unit valve doesn't regenerate automatically when you press and hold the UP and DOWN buttons, start by checking the AC adapter to ensure it's properly connected. Next, verify that the outlet has power; repair the outlet or try a different one if needed. If those aren't the issue, the drive gear or drive cap assembly might be broken, requiring replacement. Lastly, a defective PC board could be the cause, which would also need replacement.
What causes a Clack Water Specialist WS1TC Control Unit valve to stall during regeneration?
If your Clack Control Unit valve is stalled during regeneration, there are several potential causes: 1. The motor might not be operating, in which case you should replace it. 2. There may be no electric power at the outlet, so repair the outlet or use a working one. 3. The AC adapter could be defective, requiring replacement. 4. The PC board might be defective, and you'll need to replace it. 5. The drive gear or drive cap assembly could be broken, necessitating replacement. 6. A broken piston retainer could be the culprit, so replace it. 7. Finally, the main or regenerant piston might be broken, requiring replacement.
Why Clack Water Specialist WS1TC Control Unit valve regenerates manually but not automatically?
If your Clack Control Unit valve does not automatically regenerate (but does when you press and hold the UP and DOWN buttons), it could be due to a defective PC board, which would require replacement. Alternatively, there may be a set-up error, so double-check the control valve set-up procedure.
Step-by-step guide for initiating manual regeneration.
Essential safety precautions and operating guidelines for installation and use.
Summary of key technical specifications for the control valve.
Explanation of the four bypass valve positions.
Step-by-step guide for initial system configuration.
Procedures for installer display and regeneration settings.
Procedures for power outages and error messages.
Diagrams illustrating service and backwash water flow.
Diagrams illustrating brine and rinse flow.
Diagram illustrating the fill cycle water flow.
Instructions for servicing the drive assembly.
Graphs showing injector flow rates in US units.
Graphs showing injector flow rates in metric units.
Details of the product warranty terms.
General| Model | WS1TC |
|---|---|
| Type | Control Unit |
| Valve Size | 1" |
| Operating Pressure | 20 - 125 psi |
| Display | LCD |
| Timer Type | Electronic |
| Cycle Settings | Adjustable |
| Bypass | Optional |
| Valve Material | Noryl |
| Inlet/Outlet | 1" NPT |
| Manufacturer | Clack |
| Valve Type | Time Clock |
| Operating Temperature | 34 - 120°F (1 - 49°C) |
| Materials | Noryl |
| Drain Line | 1/2" NPT |
| Brine Line | 3/8" |
| Riser Tube Diameter | 1.05" |
To Next Page
