Clarion CMD8 User Manual (English)

Questions and Answers:

M
Megan BrownSep 6, 2025
What to do if there is no audio output from my Clarion Marine Audio?
- P
  paulahardingSep 6, 2025
  If you experience no or low audio output, consider the following: * Check the wiring and correct any improper audio output connections. * Increase the volume level if it is set too low. * Replace the speakers if they are damaged. * Adjust the channel balance to the center position if the volume balance is heavily biased. * Insulate all speaker wiring connections if the speaker wiring is in contact with a metal part of the boat.
L
lpayneAug 22, 2025
Why does my Clarion CMD8 Marine Equipment unit reset itself when the engine is off?
- L
  Laura SimsAug 22, 2025
  If your Clarion Marine Equipment unit resets itself when the engine is off, the connection between the ACC and the battery might be incorrect. Check the wiring and correct any issues found.
F
fpayneSep 3, 2025
What to do if there is no sound heard with the display “No File” shown on Clarion CMD8?
- C
  Christine StuartSep 3, 2025
  If you hear no sound and the display shows “No File” on your Clarion Marine Equipment, it's likely that no MP3/WMA files are stored on the USB device. Ensure that these files are properly stored on the USB device.
J
jasmin78Sep 2, 2025
What to do if Clarion CMD8 USB device is not recognized?
- S
  sarah23Sep 2, 2025
  If your Clarion Marine Equipment doesn't recognize the USB device, it could be damaged. Disconnect the USB device and reconnect it. If it's still not recognized, try replacing it with a different USB device.
N
Nicole GreenAug 31, 2025
How to fix Clarion CMD8 when USB device cannot be inserted?
- A
  Andrew HardinAug 31, 2025
  If you are unable to insert a USB device into your Clarion Marine Equipment, it may be because the USB device has been inserted in the wrong direction. Reverse the connection direction and try again. It could also be due to a broken USB connector. In this case, replace it with a new USB device.
H
Harold BatesAug 30, 2025
Why is the sound bad when Clarion Marine Equipment is first turned on?
- T
  Timothy BrownAug 30, 2025
  If the sound is bad when you first turn on your Clarion Marine Equipment, condensation may have formed on the internal lens due to the boat being parked in a humid place. Let the unit dry for about 1 hour with the power on.
W
walkerjosephAug 29, 2025
What to do if disc cannot be loaded into Clarion CMD8 Marine Equipment?
- R
  Ryan WalkerAug 29, 2025
  If you can't load a disc into your Clarion Marine Equipment, it might be because another disc is already loaded. Eject the current disc before trying to load a new one. Alternatively, there might be an object inside the unit; remove any obstructions.
D
David Smith IIAug 27, 2025
What to do if sound skips or is noisy on Clarion CMD8 Marine Equipment?
- B
  Barbara CollinsAug 27, 2025
  If the sound skips or is noisy on your Clarion Marine Equipment, the compact disc may be dirty. Clean the compact disc with a soft cloth. Alternatively, the compact disc may be heavily scratched or warped. Replace it with a compact disc with no scratches.
L
Laurie TrujilloAug 26, 2025
Why is the sound quality poor or distorted on my Clarion Marine Equipment?
- L
  lauren55Aug 27, 2025
  If your Clarion Marine Equipment exhibits poor sound quality or distortion, consider these potential causes: 1. The disc used might be non-standard; try using a standard disc. 2. The speaker power rating might not match the unit; consider replacing the speakers. 3. There might be wrong connections or a shorted speaker; in this case, check the wiring and correct any issues.
T
Thomas MaloneAug 25, 2025
Why is there no or low audio output from my Clarion Marine Equipment?
- S
  Sean WalkerAug 26, 2025
  If you're experiencing no or low audio output from your Clarion Marine Equipment, there are several things to check: * Ensure the audio output connection is properly wired and correct any issues. * Increase the volume level if it's set too low. * If the speakers are damaged, replace them. * Adjust the channel balance to the center position if it's heavily biased. * Make sure the speaker wiring isn't in contact with any metal parts of the boat; if it is, insulate the connections.

Clarion CMD8 Specifications

General

Tuner type	Digital
AM band range	530 - 1710 kHz
FM band range	87.9 - 107.9 MHz
Supported radio bands	AM, FM
Frequency range	20 - 20000 Hz
Optical drive type	Player
Cassette deck	No
Equalizer	Yes
Audio formats supported	MP3, WMA
Display type	LCD
Product color	Black, Silver
Power source	-
DC input voltage	14.4 V
USB 2.0 ports quantity	1
RMS rated power	- W