Clarion CZ505

Audio
Setup
Press the [
.P
]
button to enter sound effect
setting mode. First press shows current
EO.
Rotate the [VOLUME] knob to changes BEAT
EO
in
this order:
OFF
->
B-BOOST
->
IMPACT
->
EXCITE
->
CUSTOM
Rotate
the
[VOLUME]
knob
to
changes
CUSTOM,
and press the
[VOLUME]
knob,
the press [
~
] or [
..,._..
] button to
select
it
including: BASS-G
->
BASS-F
->
BASS-O
->
MID-G ->
MID-F
->
MID-Q
->
TREBLE-G ->
TREBLE-F
->
TREBLE-0,
rotate the [VOLUME]
knob to
select
a
value.
BASS-G
I
MID-G
I
TREBLE-G: (-7)- (+7)
BASS-F: 50
I
100
I
200
BASS-O: 0.7
I
1.0 I
1.4
I
2.0
MID-F: 50011
K
I
2K
MID-0: 0.7
I
1.0
I
1.4
I
2.0
TREBLE-F: 5k
I
1
Ok
I
15k
TREBLE-Q:
0.7
I
1.0
I
1.4
I
2.0
Press the [
.P
]
button, then press [
~
) or
[
..,._..
]
button
to
select
USER
preset
including:
BALANCE
->
FADER -> M-B EX -> HPF
(high pass filter)
->
LPF (low
pass
filter)
->
SUBW VOL
(Subwoofer
Volume), rotate the
[VOLUME] knob to
select
a
value.
BALANCE: LEFT 1-7
->CENTER->
RIGHT
1-7
FADER:
FRONT 1-7
->CENTER->
REAR
1-7
M-BEX:
ON
I OFF
HPF:
THROUGH
I 60
I
90 I
120
LPF:
THROUGH
I 60
I
90
I
120
SUBW VOL:
(-6)-
(+6)
Radio Operations
Select tuner as
playing
source
Press
[<!.>
1
SAC] button once or more to enter
RADIO
mode.
Selecting the radio
band
Press the [BAND] button
on
the
panel
or
on
the remote
control
to
select
one radio band
among
FM1, FM2, FM3,
AM.
Manual
tuning
During
manual
tuning, the frequency
will
be
changed
in
steps.
Press the
[...,..]
or [
~]
button
on
the
panel
to tune in a
lower
I
higher station.
Press the
[...,..]
or [
~]
button
on
the remote
control
to
select
preset stations.
Auto
tuning
Press and
hold
the [
...,.. ) or [
~
) button to
seek a lower
I higher station.
To stop searching, repeat the operation above
or press other buttons having radio functions.
Note:
When a station
is
received, searching stops
and the station is
played.
Preset scan
Preset scan receives the stations stored
in
preset memory in order. This function is
useful
when searching for a desired station
in
memory.
1.
Press the
[SCN/PS/AS]
on the remote
control
button.
2.
When
a
desired
station
is
tuned
in,
press the
[SCN/PS/AS] button again to
continue receiving that station.
Note:
Be
careful
not to press and
hold
the [SCN/
PS/AS]
button
for
1
second
or
longer,
otherwise the auto store function will
begin
and the unit starts storing stations.
Auto
store
The unit stores the strongest stations found
in
the entire Band.
Press and
hold
the [BAND/ASAC]
button
(1
sec.) or
[PSIAS]
button
on
the remote
control
to start automatic station search.
To stop auto store, press other buttons having
radio functions.
Notes:
1.
After auto
store,
the
previous stored stations
will
be
overwritten.
2. The unit has 4 bands, such as
FM1,
FM2,
FM3
and
AM
. FM3 and
AM
can store
by
AS
function. Each band can store 6 stations,
CZ505
can store 24 stations
in
total.
Manual store
When one expected radio station has been
detected, press and
hold
number button 1-6
to store
it
in
the memory.
Recall the
stored
stations
Press one numeric button among 1 to 6
on
the
panel
to
select
the corresponding stored
station.
Local
seeking
When
LOCAL
seeking is
ON, only
those radio
stations
with
strong
radio
signal
could
be
received.
To
select LOCAL
function, press and
hold
the
[
DISP)
button
on
the front
panel,
then press
[
~]
button
repeatedly until LO
or
OX
displays
on
the
screen,
and
rotate the [VOLUME] knob
to
select Local
or Distant mode.
Note:
The number of radio stations that can be re-
ceived
will
decrease
when
Local
mode
is
ON.
CZ505
9