IBasic
Operations
Note:
Be
sure
to
read
this chapter referring
to
the front diagrams of
chapter
"2.
CONTROLS"
on
page
3.
Be
sure
to
lower
the
volume
before sWitching
off
the
unit
power
or
the
ignition
key. The
unit
remembers
its
last
volume
setting.
If
you
switch
the
power
off
with
the
volume
up, when
you
switch
the
power
back
on, the sudden
loud
volume
may
hurt
your
hearing and damagethe
unit.
Turning
on/off
the
power
Note:
•
Be
careful about using this unit for a long time with-
out running the engine. If
you
drain
the
car's bat-
tery too far,
you
may not
be
able to start
the
engine
and this
can
reduce
the
service life of
the
battery.
1. Press the [SRC] button.
2.
The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
3.
Press and hold the [SRC] button for 1 second
or longer to turn off the power for the unit.
Selecting a
mode
1.
Press the [SRC] button to change the opera-
tion mode.
2. Each time you press the [SRC] button, the op-
eration mode changes in the following order:
Radio mode
~
CD mode
~
Radio mode...
Note:
•
If
the
CD
mode
is
selected
when
no
disc
is
inserted,
the display shows "NO
DISC".
Adjusting
the
volume
Turning the [ROTARY] knob clockwise increases
the volume; turning it counterclockwise decreases
the volume.
'"
The volume level
is
from 0 (minimum)
to
33
(maxi-
mum).
Setting
the
Z~Enhancer
This unit are provided with 3 types of sound tone
ef-
fects stored
in
memory. Select the one
you
prefer.
10 DB355MP
The factory default setting
is
Z-EHCR
OFF.
Each time you press the [Z] button, the tone ef-
fect changes
in
the following order:
Z-ENHANCER
1
~
Z-ENHANCER
2
~
Z-EN~
HANCER 3
~
Z~EHCR
OFF
~
Z~ENHANCER
1
...
• Z-ENHANCER 1 : bass emphasized
• Z-ENHANCER 2 : treble emphasized
•
Z-ENHANCER
3 : bass and treble emphasized
• Z-EHCR
OFF
: no sound effect
Audio
mode
adjustments
Press the [A-M] button to select the adjustment
mode. The mode switches as follows each time
the [A-M] button is pressed:
BASS
~
TREB
~
BAl
~
FAD
~
Previous mode
'"
The display returns
to
the
previous
mode
7 sec-
onds after the adjustment.
Adjusting
the bass
1.
Press the [A-M] button and select "BASS".
2. Turning the [ROTARY] knob clockwise empha-
sizes the bass; turning it counterclockwise at-
tenuates the bass.
* The factory default setting
is
"0". (Adjustment
range:
-7
to
+7)
Adjusting
the
treble
1. Press the [A-M] button and select "TREB".
2. Turning the [ROTARY] knob clockwise empha-
sizes the treble; turning it counterclockwise
attenuates the treble.
"The
factory default setting
is
"0". (Adjustment
range:
-7
to
+7)
Adjusting
the
balance
1.
Press the [A-M] button and select
"BAl".
2.
Turning the [ROTARY] knob clockwise empha-
sizes the sound from the right speaker; turn-
ing
it
counterclockwise emphasizes the sound
from the left speaker.
*The factory default setting
is
"0". (Adjustment
range: L
13
to
R13)
To Next Page
Loading...
Need help?
General
