Clarion DXZ938R User Manual

DXZ938R 15
English
Distributing the center channel sound to the
right and left will increase the integrated
sound field image, providing you with an
natural spatial feeling of sound.
Setting to the value 0 will produce the center
sound with the center speaker.
Setting to the value 7 will distribute the cen-
ter sound to the front speaker L/R as the ex-
isting stereo sound does.
AC-Processor II Operation
There are 2 modes “STD” (standard) and “PRO”
(professional) in the AC-ProII .
1. Setting the speaker to 4ch+2ch (For details,
refer to the subsection “Speaker Setting” in
the section “Basic Operations”).
2. Turn off the PLII mode.
3. Press and hold the [TITLE] button for 1 sec-
ond or longer and enter “ADJ” mode.
4. Press the [a] or [d] button to select the
“AC-PII SEL”.
5. Press the [
] button to select AC-ProII
mode from “STD” or “PRO”.
6. Turn the [ROTARY] knob clockwise or coun-
terclockwise to select “STD” or “PRO”.
7. Press the [TITLE] button to the previous
mode.
Operation AC-P II STD
1. Press the [VSE] button to enter VSE mode.
2.
Press the [BND] button to select “VSE BASIC”.
3. Press the [DIRECT] button to select VSE
menu as below.
1. Flat: original sound, flat equalizing
2. Bass boost: deep bass sound empha-
sized
3. High boost: middle and high sound area
emphasized
4. Impact: low and high sound area em-
phasized
5. Acoustical: middle sound area empha-
sized (human voice)
6. Smooth: quiet and graceful feeling
4. Press the [VSE] button to return to the previ-
ous mode.
5. Press and hold the [VSE] button for 1 second
or longer so that the VSE effect is turned on
or off.
Adjusting AC-P II STD
AC-PII STD makes natural stereo feeling for ev-
ery seat by virtual space enhancer.
VSE, which is room simulation, can correct the
sound pressure inside the car so that the uni-
form sound effect is obtained at any seats.
1. Select “VSE” menu which you want to edit on
the basis of.
2. Press and hold the [TITLE] button for 1 sec-
ond or longer.
3. Press the [a] or [d] button to select item
to be adjusted.
There are “DIFFUSE” “CAR WIDTH” and “CAR
LENG” available for the items to be adjusted.
AC-Processor II Operation
DIFFUSE (Adjusts the correction
deviation of broadness)
CAR WIDTH (Adjusts the correction
deviation of width inside
the car)
CAR LENG (Adjusts the correction
deviation of length inside
the car)
4. Turn the [ROTARY] knob clockwise or coun-
terclockwise to make the adjustment.
The adjustment range is from 1 to 10 for
each item.
5. Press and hold the [DIRECT] buttons for 2
seconds or longer to store the edited con-
tents.
∗ You can give a title to user memory. For the in-
putting method of titles, refer to the subsection
“Entering titles” in section “Operations com-
mon to each mode”.
Operation AC-P II PRO
Arrival time of sound from the speaker can be
selected from among five types according to the
position of the seat. In addition, Time Alignment
Function enables a pinpoint speaker setting to
obtain a uniform sound effect from speakers to
the listner.
1.
Press the [VSE] button to enter POSITION mode.
2. Press the Band button to select “POS BASIC”.
3. Press the [DIRECT] button to select VSE
menu as below.
1.FRONT-L 2.FRONT-R 3.FRONT 4.REAR
5.FULL SEAT
4. Press the [VSE] button to return to the previ-
ous mode.

Clarion DXZ938R Specifications

Radio Specifications

FM receiving frequency range	87.5 to 108 MHz (0.05 MHz steps)
MW receiving frequency range	531 to 1602 kHz (9 kHz steps)
LW receiving frequency range	153 to 279 kHz (3 kHz steps)

CD Player Specifications

frequency response	5 Hz to 20 kHz (± 1 dB)
signal to noise ratio	100 dB (1 kHz) IHF-A
dynamic range	96 dB (1 kHz)

General Specifications

output power	4 x 31 W (DIN 45324, +B=14.4V)
power supply voltage	14.4 V DC (10.8 to 15.6 V allowable)
power consumption	Less than 15 A

Weight and Dimensions

main unit weight	1.7 kg
remote control unit weight	30 g (including battery)
main unit dimensions	178 (W) x 50 (H) x 155 (D) mm