Clarion DXZ938R User Manual

16 DXZ938R
English
5. Press and hold the [VSE] button for 1 second
or longer so that the POSITION effect is
turned on or off.
Adjusting AC-P II PRO
1. Select “VSE” menu which you want to edit on
the basis of.
2. Press and hold the [TITLE] button for 1 sec-
ond or longer.
3. Press the [a] or [d] button to select item
to be adjusted.
∗ There are “TIME ALIGN” and “SP GAIN” avail-
able for the items to be adjusted.
4. Press the [ ].
5. Press the [a] or [d] button to select the
channel to be adjusted. Available channels
are: “FRONT-L”, “FRONT-R”, “REAR-L”,
“REAR-R”, “SW-L” and “SW-R”.
6. Turn the [ROTARY] knob clockwise or coun-
terclockwise to make the adjustment.
The adjustment of “TIME ALIGN” range is
from 0 cm to 500cm.
The adjustment of “SP-GAIN” range is from
0db to -20dB for each channel.
7. Press and hold the [DIRECT] buttons for 2
seconds or longer to store the edited con-
tents.
∗ You can give a title to user memory. For the in-
putting method of titles, refer to the subsection
“Entering titles” in section “Operations com-
mon to each mode”.
EQ Operation
There are 2 mode for sound EQ “P.EQ” mode
and “BASS/TREB” mode selecting EQUALIZ-
ING mode.
1. Press and hold the [TITLE] button for 1 sec-
ond or longer and enter “ADJ” mode.
2. Press the [a] or [d] button to select the
“AC-PII SEL”.
3. Press the [
] button to enter AC-PROII
select mode “STD” or “PRO”.
4. Then press the [a] or [d] button to select
the “EQ SEL”.
5. Turn the [ROTARY] knob clockwise or coun-
terclockwise to select “P.EQ” or “BAS/TREB”
mode.
6. Press the [TITLE] button to return to the pre-
vious mode.
∗ Factory default setting is P.EQ
AC-Processor II Operation
Operation P.EQ
A full range of frequency level can be minutely
corrected with a smooth curve by frequency cor-
rection in accordance with car models. Six kinds
of P.EQ basic menus have been pre-stored in
this unit according to the car models and the
mounting positions of speakers. Thus, set it in
accordance with the car type.
1. Press the [EQ] button to enter “P.EQ mode”.
2. Press the Band button to select “P.EQ BA-
SIC”.
3. Press the [DIRECT] button to select P.EQ
menu as below.
1.SEDAN-1 2.SEDAN-2 3.WAGON-1
4.WAGON-2 5.MINI VAN-1 6.MINI VAN-2
4. Press the [EQ] button to return to the previ-
ous mode.
5. Press and hold the [EQ] button for 1 second
or longer so that the P.EQ effect is turned on
or off.
Adjusting P.EQ
1. Select “P.EQ” menu which you want to edit
on the basis of.
2. Press and hold the [TITLE] button for 1 sec-
ond or longer.
3. Press the [a] or [d] button to select item
to be adjusted.
There are “FRONT/REAR” ,“BAND” ,“FREQ”
“GAIN” and “Q” available for the items ad-
justed.
4. Press and hold the [DIRECT] buttons for 2
seconds or longer to store the edited con-
tents.
∗ You can give a title to user memory. For the in-
putting method of titles, refer to the subsection
“Entering titles” in section “Operations com-
mon to each mode”.
∗ The parameter created in this section is also
effective when the unit is in both the “STD”
and “PRO” mode.

Clarion DXZ938R Specifications

Radio Specifications

FM receiving frequency range	87.5 to 108 MHz (0.05 MHz steps)
MW receiving frequency range	531 to 1602 kHz (9 kHz steps)
LW receiving frequency range	153 to 279 kHz (3 kHz steps)

CD Player Specifications

frequency response	5 Hz to 20 kHz (± 1 dB)
signal to noise ratio	100 dB (1 kHz) IHF-A
dynamic range	96 dB (1 kHz)

General Specifications

output power	4 x 31 W (DIN 45324, +B=14.4V)
power supply voltage	14.4 V DC (10.8 to 15.6 V allowable)
power consumption	Less than 15 A

Weight and Dimensions

main unit weight	1.7 kg
remote control unit weight	30 g (including battery)
main unit dimensions	178 (W) x 50 (H) x 155 (D) mm