EasyManua.ls Logo

CMi C-EMH-2400 40 - Service and Maintenance; Personal Protective Equipment; Electrical Safety Precautions

CMi C-EMH-2400 40
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
27
Young people under 18 years of age and users
who are not sufficiently acquainted with its oper-
ation must not use the device.
Wear the personal protective equipment when
working with the device
Do not operate the device without installing the
protection devices.
If dust extraction and collection devices can be
fitted, make sure that they are connected and
used correctly. Using a dust extractor can
reduce hazards caused by dust.
Keep children and other persons away when
using the device. Distractions may cause you to
lose control of the device.
Wear suitable clothing. Do not wear loose cloth-
ing or jewellery. Keep hair, clothing and gloves
away from moving parts. Loose clothing, jewel-
lery or long hair can get caught up in moving
parts.
Service
Have your device repaired only by qualified tech-
nicians, using only genuine spare parts. This will
maintain the safety of the device.
Maintenance
Completely switch off the device itself before
working on it.
Only the maintenance work and trouble shooting
activities described in this instructions for use
may be carried out. All other work must be car-
ried out by an expert.
Check all screw connections regularly to ensure
a tight fit. This will maintain the safety of the
device.
Use only genuine spare parts. Only these spare
parts are designed and suitable for the device.
The use of other spare parts not only voids the
warranty, you can also endanger yourself and
your environment.
Storage and transport
Always store the device in a dry place.
Store the device in a frost-free place.
Protect the device from damage during trans-
port.
Personal protective equipment
Explanations on the device
Symbols appearing on your device may not be
removed or covered. Signs on the device that are no
longer legible must be replaced immediately.
Electrical safety
The equipment shall be clearly marked as being
suitable for use only in permises having a service
current capacity equal to or greater than 100A
per phase.
The connector plug on the product must fit into
the socket. Under no circumstances alter the
plug. Do not use earthed electrical tools in con-
junction with an adapter. Unmodified plugs and
suitable sockets reduce the risk of electric
shock.
Avoid physical contact with grounded surfaces,
such as those of pipes, radiators, cookers and
refrigerators. The risk of electric shock increases
if your body is earthed.
Keep electrical tools away from rain and wet.
The risk of electric shock increases if water pen-
etrates an electrical tool.
Switch off device in case of power interruption
and pull mains plug. This prevents the uninten-
tional use of the use in case of voltage return.
Check whether the locking device is locked and
lock this if required in case of power interruption
and each setting of the device. Otherwise the
device may start unexpectedly when the power
is supplied.
Do not use the cable to carry the product, hang
it up or pull the plug out of the socket. Keep the
cable away from heat, oil, sharp edges and any
moving machine parts. Damaged or tangled
cables increase the risk of electric shock.
If the connecting cable becomes damaged, it
must be replaced by an expert.
If you require to work with an extension cable,
this must be approved for this application field
and must have sufficient cross-section. Other-
wise power loss in case of the device and over-
heating of the cable may occur. If you are not
certain, contact a specialist.
If you use an electrical tool outdoors, use only
extension cables suitable for outdoor use. Using
an extension cable that is suitable for outdoor
use reduces the risk of electric shock.
Wear goggles while you are working.
Wear hearing protection while you are
working.
Wear protective gloves when working.
Wear safety shoes when working.
Read the instructions for use before use
Observe all safety instructions in the oper-
ating instructions!
Protection class II
Risk due to rotating cutting tools!
Risk of injuries due to cutting!
Before carrying out cleaning and mainte-
nance, wait for the cutting tool to stop.
STOP
GB
Haecksler_468289.book Seite 27 Donnerstag, 7. April 2016 8:53 08

Table of Contents