CO/Tech MBY8-UK - Page 3

3
ENGLISH
11. Do not damage theelectric cable. Nevercarry themachine by its electric cable. Donot pull thecable but
instead pull out theplug when cutting off power. Makesure thecable does not come into contact with heat,
oil or sharpedges.
12. Secure work material properly. Useclamps or vices where possible, allowing you to manage thetool with
both hands. Itis safer than securing work material with onehand.
13. Do not stretch yourself toofar. Makesure that you adopt asecure and balanced posture thewholetime.
14. Keep thetools intrim. Makesure they are clean and that theedges are kept sharp for optimal
effect and greater results. Followthemanual’s recommendations for lubricating and changing parts.
Checktheelectrical cable regularly; if damaged it should be replaced by qualified service technicians.
Inspect all extension cables regularly so that they are not damaged. Makesure that themachine’s/tool’s
handles and levers are dry, clean and free from oil, grease etc.
15. Turning off thepower. Pullout theplug and press emergency stop (if one exists) before service and
replacement of attachments such as plane irons, drills, bits, emery cloth or knives.
16. Remove all keys and service tools. Makeahabit of checking that all keys and service tools are removed
from themachine before turning on thepower.
17. Avoid accidental starts. Donot carry atool with one finger on thepower button if thecable is in thesocket.
Makesure that thepower button is set to OFF when plugging in.
18. Use correct extension cables. Ifyou use extension cables outdoors, only use ones intended for outdoor use.
Useextension cables with sufficient conductor lead area and unwind theentire cable.
19. Use common sense and be careful. Thinkbefore carrying out atask so that you are able to carry it out
correctly. Neveruse themachine/tool when you are tired, on medication etc.
20. Check that all parts are undamaged. Checkbefore starting up thetool: that all protective parts and other
parts are undamaged and fulfil their function; that rotating parts rotate freely and are correctly aligned; that
no moving parts can get stuck; that no defect or other factors have emerged that may hamper thework’s
performance. Acover or other part that is damaged should be repaired per part or be replaced. Damaged
electrical cables and power switches should always be replaced by professionals. Neveruse thetool if you
can not turn it on or off safely.
21. Use recommended parts. Usingnon-recommended parts can cause accidents or risk personal injury.
22. Repaired only by qualified technicians. Thetool corresponds to current safety standards. Repairs on thetool
should always be carried out by professionals using original reserve parts, otherwise thetool may cause
accidents or riskfor personal injury.
23. Electrical tools should be connected to themains via acircuit-breaker to insure personal safety! Theproduct
may not be changed or used for tasks it is not designed for! Regularly check that all screws and bolts are
properly tightened!
3. Safety instructions for surface plane
1. WARNING! Donot use theplane until it is completely assembled and connected according to
theinstructions in this manual.
2. If you are not completely sure as to how asurface plane works: Askacarpenter or other qualified person
foradvice.
3. Insure that theelectrical installation is carried out correctly. Aqualified electrician must be employed for
permanent connections. Onlyuse earthed sockets.
4. Perform all adjustments with thepower switched off.
5. Pull out electrical cable plugs before repairing.
6. Never turn thepower on before you have removed everything on thetable (tools, waste, etc.).
7. Make sure that theplane irons are sharp with no traces of rust orresin.
8. Never plane without correctly mounted and adjusted protective covers.
9. Do not place fingers near thecutter and plane’s surface.
10. Never place hand beneath thecutter when motor is running.
11. Do not place fingers in front of shaving disposal vent. Thecutter rotates incredibly fast.
12. Never feed anything in from theoutflow end.
13. Always make sure work materials are properly secured.