Craftsman 113.225909 User Manual

Save This Manual
For Future Reference
MODEL NO.
113, 225909
BELT AND DISC
SANDER ONLY
MODEL NO.
113.225931
BELT AND DISC
SANDER!WITH
LEGS AND MOTOR
Serial
Number
Model and serial
number may be found
at the right hand side
of the base,
You should record both
model and serial number
in a safe place for
CAUTION:
Read SAFETY
INSTRUCTIONS
carefully
BEL T AND D/SC SANDER
. assembly
® operating
o repair parts
Sold by SEARS, ROEBUCK AND CO., Chicago, iL. 60684 U.S.A.
Part No. 68073 Printed in USA

Craftsman 113.225909 Specifications

General

Brand	Craftsman
Model	113.225909
Category	Sander
Language	English

Summary

FULL ONE YEAR WARRANTY ON CRAFTSMAN BELT AND DISC SANDER

general safety instructions for power tools

electrical requirements

CONNECTING TO POWER SOURCE OUTLET

Instructions for connecting the sander to a power outlet, emphasizing proper grounding and outlet types.

CHECK MOTOR ROTATION

Procedure to verify the motor shaft's rotation direction before connecting power.

unpacking and checking contents

TOOLS NEEDED

Lists all necessary tools required for assembly and initial setup of the sander.

assembly

HARDWARE FOR MOUNTING TOOL & MOTOR

Specific hardware components required for securely mounting the tool and its motor.

ASSEMBLING STEEL LEGS

Step-by-step guide for assembling the steel leg stand structure.

MOUNTING BELT AND DISC SANDER ON CRAFTSMAN STEEL LEG SET.

Instructions for attaching the main sander unit to the assembled steel leg set.

INSTALLING SANDING DISC AND DUST TRAP

Guide for correctly installing the abrasive disc and its associated dust trap.

INSTALLING MOTOR, V-BELT, AND BELT GUARD

Steps for fitting the motor, V-belt, and the protective belt guard assembly.

ON-OFF SWITCH

Instructions for installing and using the power switch, including its safety locking feature.

INSTALLING WORK TABLE

Procedure for installing and positioning the work table relative to the abrasive disc.

INSTALLING ABRASIVE BELT-TENSIONING AND TRACKING

Steps for fitting the belt, applying tension, and ensuring proper tracking.

INSTALLING BACKSTOP

Instructions for installing the backstop component for workpiece support.

getting to know your belt and disc sander

ABRASIVE BELT ADJUSTING SCREWS

Explains the function of belt adjusting screws for tension and tracking.

ABRASIVE BELT LOCKING SCREWS

Details the screws used to secure the belt adjustment settings.

WORK TABLE TILT LOCK SCREW

Describes the screw that locks the work table's tilt angle in place.

BACKSTOP LOCK SCREW

Information on the screw that secures the backstop in its desired position.

BELT TABLE LOCKING BOLTS

Covers the bolts used to lock the belt table, including adjustments for vertical position.

ABRASIVE BELT TABLE STOP

Guidance on adjusting the abrasive belt table stop for proper leveling.

basic operation

SURFACE FINISHING ON THE ABRASIVE BELT.

Techniques for finishing flat surfaces using the abrasive belt.

END FINISHING ON THE ABRASIVE BELT.

Method for finishing the ends of workpieces on the abrasive belt.

FINISHING CURVED EDGES ON THE ABRASIVE BELT

How to finish curved edges on the abrasive belt.

FINISHING SMALL END SURFACES AND CURVED EDGES ON THE ABRASIVE DISC

Techniques for finishing edges on the abrasive disc.

maintenance

MOTOR MAINTENANCE AND LUBRICATION

Procedures for maintaining and lubricating the tool's motor and its components.

lubrication

Details on lubrication for bearings and the idler pulley mechanism.

trouble shooting

TROUBLE SHOOTING -- MOTOR

Common motor-related problems and their solutions.

repair parts

HARDWARE FOR MOUNTING TOOL & MOTOR

Lists specific hardware components for mounting the tool and motor.

HOW TO ORDER REPAIR PARTS

Guide on how to obtain replacement parts from Sears, including necessary information.

MOTOR CONNECTIONS