Current eFlux User Manual

IMPORTANT: Please refer to additional safety warnings on last page.
- eFlux wave pumps create a tremendous amount of water flow. Do not install pump where the
strong current can harm corals or animals.
- Do not install pump too close to the sand bed where it will not stir/suck the sand.
- Pumps can also produce powerful waves in both wave and surge mode. Ensur
e your aquarium is
designed for wave pumps and ensure pumps ar
e mounted low enough not to push water out of the
aquarium.
- Magnet mounting assembly is very powerful. Be cautious not to cause injury to fingers.
- Keep out of reach of children.
- Never place magnets or pump near sensitive electronics, sharp objects or attractive surfaces.
- Never run wave pump dry or out of water.
- Always place spacer between magnets when not in use.
- Always unplug with dry hands for any maintenance or service.
- eFlux wave pumps are 24VDC. Ensure one 24VDC UL® transformer is used per wave pump.
- Ensure 24VDC UL® transformer is plugged into a GFCI approved outlet with a drip loop.
- Turn controller OFF and disconnect pump from power before performing any service
- Ensure eFlux wave pumps and any accessories all have a drip loop installed before plugging into
the wave pump manifold HUB as shown below.
SAVE THESE INSTRUCTIONS
AC Power
GFCI Outlet
24VDC
Power Supply
Wave Pump
LED Display
Wave Pump
Manifold HUB
P1P3
P2
LCK P/S SRE SUR PUL FRE FLO
24VDC
Power Supply
Drip
Loop
Drip
Loop
Ensure use of drip
loop for all cables
Use only with GFCI
Protected AC Outlet
Ensure correct voltage power
supply for each component
Use caution when
installing magnets
Ensure pump location
will not spill water from
wave motion
Ensure use of drip
loop for all cables
Safety Instructions & Warnings 1
What’s Included & Installation 2
eFlux Wave Pump Installation 3
Cable Connections 4
Programming Guide 5-9
Safety Warnings & Warranty 10
Thank You!
For purchasing our eFlux Wave Pump Kit.
Please read all instructions before
getting in the LOOP!
eFlux Wave Pump Kit
Safety Instructions & Warnings
Table of Contents
Page 1

Current eFlux Specifications

General

Category	Water Pump
Model	eFlux
Max Head Height	16.4 ft (5m)
Voltage	DC 24V
Controller	Included
Modes	Variable Speed
Power Source	DC

Summary

Safety Instructions & Warnings

General Safety Precautions

Essential safety guidelines for operating the eFlux Wave Pump Kit, covering handling and environment.

What's Included

Kit Components Overview

Lists all items included in the eFlux Wave Pump Kit for user verification.

Optional Accessories and Replacement Parts

Accessory and Replacement Part Options

Details available optional accessories and specific replacement parts for the wave pump system.

Installation Instructions

Pump Installation Steps

Guide on physically mounting and positioning the eFlux wave pump within the aquarium.

Manifold Hub and LED Display Installation

Instructions for installing the wave pump manifold HUB and the LED display bracket and sensor.

Cable Connections

Connecting Wave Pump Components

Step-by-step instructions for connecting the wave pump, LED display, and power supply.

Programming Guide: Remote and Display Overview

Remote Control Functions

Explains the functions of each button on the eFlux Wave Pump wireless remote control.

Pump LED Display Indicators

Details the indicators and display elements on the eFlux Wave Pump LED display.

Programming Guide: Basic Operations

Pump Power Control

Instructions for turning all pumps on/off and controlling individual pumps.

Remote Lock and Feed Mode

How to lock/unlock the remote and activate the FEED mode for pumps.

Flow Mode Selection Overview

Introduction to selecting flow modes (Stream/Steady) for pumps.

Programming Guide: Advanced Flow Modes

Surge/Gyre Flow Mode

Details how to set Surge/Gyre mode, flow rate, and frequency for wave motion.

Wave/Pulse Flow Mode

Explains setting Wave/Pulse mode, including flow rate and pulse frequency.

Flow Mode Application Guide

Compares Stream/Steady, Surge/Gyre, and Wave/Pulse modes for different aquarium applications.

Programming Guide: Detailed Configuration

Designating Pump and Flow Mode

Steps to select the pump and desired water flow mode (Stream, Surge, Wave).

Setting Flow Rate and Frequency

Adjusting maximum flow rate and frequency/duration for selected modes.

Programming Guide: Pump Syncing

Primary/Secondary Pump Syncing (GYRE)

Guide on synchronizing pumps for GYRE flow by setting primary and secondary roles.

Programming Pump 1 (Primary)

Instructions for setting Pump 1 into a desired mode and adjusting its parameters.

Programming Pump 2 (Secondary/Primary)

How to configure Pump 2 as either a secondary (sync) or independent primary pump.

Safety Warnings and Warranty Information

Important Safety Warnings Summary

Key safety precautions and warnings for using the eFlux Wave Pump Kit.

Drip Loop Importance

Explanation of why drip loops are essential for electrical safety with this product.

One Year Limited Warranty

Details of the product's warranty coverage, limitations, and claims process.