Curtis CAFE PC1 - Advanced Programming and Maintenance; Manual Liquid Dispense Setup; Temperature Control; Error Codes and System Flushing

Numberof
Blinks
80ºF
85ºF
90ºF
95ºF
100ºF
105ºF
110ºF
120ºF
140ºF
185ºF
190ºF
192ºF
194ºF
196ºF
198ºF
200ºF
202ºF
204ºF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Temperature
TemperatureSettings
Conrm/Reset Temperature (Factory set at 190ºF . . . Cold Capppuccino set at 100ºF)
Enter Program Mode – pressandholdSTOP/WASHforaboutten[10]secondsuntilalllightsonthecontrolpanel
areblinking.
Set Manual Dispense –Whileyouareintheprogrammingmode,pressandholdthePUSHbutton.
Hotliquidwillstarttoow.
ContinuetoholddownthePUSHbuttonuntilliquidstopsowing,thenreleasethebutton.
Atthistime,youhaveselectedtheManualLiquidDispensingModeandhaveexitedoutoftheprogrammingmode.
Thesefeaturesallowyoutochecktheheatingtanktemperatureorchangethetemperatureifdesired.Thetem-
peratureinthetankisprogrammablefrom80ºF,in2degreeincrementsupto140ºF,thentemperaturewilljump45
degreesto185ºF,thenresume2degreeincrementsuptoamaximum204°F(seeTemperatureSettingstable,right).
To Conrm Temperature.PressandholdSTOP/WASHbuttonforapproximately2-3seconds.WhentheREADY
lightstartsblinking.LiftofffromSTOP/WASHbutton.Eachblinkequals2ºF,startingwith80ºF,toamaximumof204ºF.
Enter Temperature Program Mode.PressandholdSTOP/WASHbutton.READYlightwill
start“quickashing”.
To Change Temperature.ReleaseSTOP/WASHbutton,thenpressandholdagain.Each
quickashequals2ºF.ReleaseSTOP/WASHwhendesiredtemperatureisreached.
To Set and Exit,presseitherofthePUSHbuttons.
To Change Tank Temperature
Programming Continued ...
3
WATER LEVEL PROBLEM 3LONGAND1SHORT
Whenobservingthiscodeontheswitchpanel,beawarethereisamalfunctioninthewaterlevel
control system.
TEMPERATURE SENSOR PROBLEM 3LONGAND2SHORT
Wheneverthislightpatternisseenashingonthecontrolpanelyouareexperiencingatankheating
system failure.
ERROR CODES:CurtisCafesystemscontainvarioussafetyfeaturesintheelectroniccircuitrythatshutdownthefunctionsoftheunitintheeventofasystem
failure.ErrorcodesaresignalledbytheREADY lightblinkingoneoftwopatterns:
FlushingtheWhipperChambers
Everythreetofourhoursormoreoftenifnecessaryushthewhipperchamber/dispensingsystem.
 A. MakesurepowerisON.
 B. PressandholdtheSTOP/WASHbutton.SelectoneofthePUSHdispensingbuttonsandpress.Hotrinse
   waterwillushoutthesystem.LiftofftheSTOP/WASHbuttonwhenwaterrunsclear.
 C. Cleanupanywaterthatmayhavespilled.
Cleaning
 A.Switchofftheunitatthepowertoggleswitch,markedCONTROL,behindtheunit.
 B.Wipeallexteriorsurfaceswithadampcloth;removinganyspills,dustordebrisfromtheunit.
 C.Removethedriptrayandlouveredscreenandwashoutitscontents.Forhardtocleandeposits,useamild
  detergentsolution.
 D.Cleanaroundthedispensingarea,wipingwithanontoxiccleaner.
CAUTION:
DO NOT use
undiluted bleach
or chlorine.