Need help?Do you have a question about the D&R AIRENCE and is the answer not in the manual?
Details the features of the USB input module.
Describes the Telco input module for telephone line connections.
Outlines the controls and functions of the master section.
Explains the features of the extender unit for expanding inputs.
Details the rear panel connectors of the main mixer unit.
Describes the rear panel connectors of the extender unit.
Explains how to adjust input signal levels.
Details the stereo line and USB input connections and settings.
Describes the balanced XLR microphone input and its features.
Explains the three-band equalizer for tone control.
Describes routing signals to the Sub and Program buses.
Details the stereo Aux send for external effects.
Explains the cue function for pre-fade listening and communication.
Details the 100mm fader operation and fader start switch.
Lists the five connectors on each module.
Describes the stereo jack insert for signal processors.
Details the balanced female XLR microphone input.
Discusses jumpers for configuring USB module settings.
Provides instructions for accessing internal components.
Explains jumpers for phantom power and low cut filter.
Details jumpers for fader gain and Aux send selection.
Describes jumpers for start pulse and non-stop source selection.
Explains jumpers for USB output selection and input level.
Details the jumper for controlling the MIC ON signal.
Guides on setting output signal to the USB connector.
Explains how to adjust signal levels for PC output.
Defines what a telephone hybrid is and its function.
Details the Telco send control and phone/line input switch.
Explains side tone attenuation adjustments.
Describes gain adjustment and the connect button for calls.
Details the talkback button for communication.
Describes the 11-segment LED bar meters.
Explains how to convert stereo to mono output.
Details routing external audio sources.
Explains the record output connections.
Describes master controls for Aux send and listening.
Details Aux return inputs and Sub send master control.
Explains Studio and Announcer output functions.
Details the CRM section for monitoring.
Explains the mute function activated by microphone.
Describes balance and split listening controls.
Details the talk back circuit and its routing.
Explains the 100mm K-Alps master faders.
Details the headphone output and impedance recommendations.
Explains the non-stop on-air function.
Describes the software metering application and clock.
Details RCA Cinch outputs for Aux Send and CRM.
Explains Program Send outputs and Aux Return inputs.
Describes EXT inputs and RCA Cinch Cue outputs.
Details Studio outputs and Record Out connections.
Explains the RCA Cinch Sub outputs.
Describes the balanced male XLR master outputs.
Details the external 36V power supply connectors.
Explains connecting extender units via Sub-D.
Covers connection and initial setup for modules 1-4.
Guides on setting up individual input channels.
Details connecting and setting up USB modules.
Step-by-step guide for setting up Telco modules.
Explains the procedure for adjusting R and C balance.
Details the GAIN, STEREO LINE/LINE, and MIC inputs.
Explains equalizer and routing functions for extender modules.
Describes Aux send and cue functions for extender modules.
Details insert and mic inputs for extender channels.
Covers jumper options for extender channels.
Introduces the control section with switches and encoder.
Explains the benefit of using the control module.
Details controlling software via USB channels.
Explains the USB HID protocol for PC communication.
Method for software developers to integrate the protocol.
Using a mapper application for end-users.
Explains how the mapper creates a virtual keyboard.
Lists control signals from the mixer.
Guides on using the configuration editor.
Details selecting sources and configuring actions.
Explains plug-ins for software functions.
Guides on creating custom plug-in files.
Overview of current configuration.
Covers connecting to mixer and saving presets.
Overview of the HID protocol for communication.
Details message structure and command bytes.
Explains messages for sending commands to the mixer.
Describes messages for reading data from the mixer.
Addresses the specific Windows 7 error.
Explains the components of a USB system.
Defines USB host and device roles.
Lists the USB components within the Airence mixer.
Analyzes potential USB bandwidth issues.
Solution for bandwidth issues by exclusive connection.
Details electrical and connection specifications for inputs/outputs.
Lists specifications for USB and Telco interfaces.
Covers frequency response, distortion, and software protocol.
Explains the need for firmware updates.
Details how to enter bootloader mode.
Guides on installing the firmware update software.
How to identify the device in bootloader mode.
Steps for installing necessary drivers.
Precautions before updating firmware.
Steps for updating the mixer's firmware.
Addresses common firmware update errors.
Troubleshoots JVM errors during update.
States compliance with EMC standards.
Provides product conformity declarations.
Outlines safety precautions and warnings.
To Next Page
General