Danfoss PVE 4 Series User Manual

V310115.A
Installation Guide
Electrical Actuating Module
PVE series 4 for PVG 32 and PVG 100
© Danfoss, 2014-03 520L0619 • Rev EB • Mar 2014 1
157R9915 157R9915
PVE for PVG 32 and PVG 100:
Oliestrømmens retning for
standard monterede grupper.
Oil ow direction for standard
assembled groups.
Richtung des Ölstroms für
Standard-Baugruppen.
Sens du débit pour ensembles
standard.
Mounting PVE
Instruktionen dækker
Instruction covers
Anleitung umfasst
l'instruction couvre
Danfoss actuators PVEA, PVEH, PVEM, PVEO, PVEP,
PVES, PVEU Variants -R, -DI, -SP, -F.
Connectors Deutsch, AMP, DIN/Hirschmann.
For full documentation see Technical Information, PVE
Series 4 for PVG 32, PVG 100 and PVG 120, 520L0553 on
www. Danfoss.com
V310348A
• Protect LVDT-pin if present
• Ensure O-rings are in place
• Ensure gasket when using AMP and DIN/Hirschmann connector
• Do not over torque
WWarning
PVEA is not for use on PVG 100.
5 [0.2]
157-743.10B
8 ±0.5 N•m
[70 ±4.4 lbf•in]
to tank
to application
P→A
For Technical Information, see Danfoss.com.

Danfoss PVE 4 Series Specifications

General

Series	PVE 4
Supply Voltage	12/24 VDC
Control Type	Closed-Loop
Communication	CAN bus
Protection Class	IP67
Housing Material	Aluminum
Input Signal	Analog or Digital
Output Signal	PWM

Summary

PVE for PVG 32 and PVG 100

Mounting PVE

PVE Connection and Version Details

Version ON/OFF

Details ground pins and feedback signal connection for ON/OFF variants.

Connection PVEO with Direction Indication (DI)

Wiring for PVEO with direction indication using AMP/Deutsch connectors.

Connection PVEO Standard

Wiring for standard PVEO models with AMP/Deutsch/Hirschmann.

DI General Note

Information on UDC and UDC2 supply for DI versions and grounding.

Proportional PVE Versions

Standard PVE

Wiring and control voltage for standard PVE (AMP, Hirschmann/DIN, Deutsch).

Standard PVE with DI

Wiring and control voltage for standard PVE with direction indication (DI).

Proportional PVE with Special Features

Standard PVE with SP

Connection and control voltage for PVE with Spool Position (SP) feedback.

PVE with Separate Float Pin

Wiring and control voltage for PVE with separate float pin (AMP, Deutsch).

PWM Controlled PVE - PVEP

Connection and control voltage for PWM controlled PVEP.

Safety and Monitoring

Fault Monitoring Overview

Summary of fault types, delay, error modes, and output status for PVE modules.

Spool Position Feedback (-SP)

Explanation of the -SP functionality and signal feedback characteristics.

Direction Indication Feedback (-DI)

Details on DI signals, spool position relationship, and signal transition values.

Technical Data

PVEO, PVEM Data

Technical specifications for PVEO and PVEM modules, including voltage and current.

PVEA, PVEH, PVEP, PVES, PVEU Data

Technical specifications for PVEA, PVEH, PVEP, PVES, PVEU modules.

Oil Viscosity and Temperature

Hydraulic oil requirements, including viscosity range and operating temperature.

Connector Versions and Protection

Information on available connector types (AMP, Hirschmann, Deutsch) and enclosure grades.

Installation and Protection

Bleeding / Purging

Recommendations for bleeding or purging the PVE modules during vertical installation.

IP Protection Class

Details on PVE modules complying with IP65 and recommendations for exposed applications.

General Warning on Valve Failure

Important note on potential valve failure and manufacturer responsibility for application safety.

Accessories and Cable Codes

Connector Code Numbers

Part numbers for accessory connector kits (AMP, Hirschmann).

Set of Seals Code Numbers

Part numbers for seal kits applicable to different PVE actuators.

Cables Code Numbers

Wire color coding and lengths for Deutsch and AMP connector cables.