42-19 Zero Speed Limit
42-2* Safe Input
42-20 Safe Function
42-21 Type
42-22 Discrepancy Time
42-23 Stable Signal Time
42-24 Restart Behavior
42-3* General
42-30 External Failure Reaction
42-31 Reset Source
42-33 Parameter Set Name
42-35 S-CRC Value
42-36 Level 1 Password
42-4* SS1
42-40 Type
42-41 Ramp Prole
42-42 Delay Time
42-43 Delta T
42-44 Deceleration Rate
42-45 Delta V
42-46 Zero Speed
42-47 Ramp Time
42-48 S-ramp Ratio at Decel. Start
42-49 S-ramp Ratio at Decel. End
42-5* SLS
42-50 Cut O Speed
42-51 Speed Limit
42-52 Fail Safe Reaction
42-53 Start Ramp
42-54 Ramp-down Time
42-6* Safe Fieldbus
42-60 Message Selection
42-61 Destination Address
42-8* Status
42-80 Safe Option Status
42-81 Safe Option Status 2
42-82 Safe Control Word
42-83 Safe Status Word
42-85 Active Safe Func.
42-86 Safe Option Info
42-88 Supported Customization File Version
42-89 Customization File Version
42-9* Special
42-90 Restart Safe Option
99-* Devel support
99-0* DSP Debug
99-00 DAC 1 selection
99-01 DAC 2 selection
99-02 DAC 3 selection
99-03 DAC 4 selection
99-04 DAC 1 scale
99-05 DAC 2 scale
99-06 DAC 3 scale
99-07 DAC 4 scale
99-08 Test param 1
99-09 Test param 2
99-10 DAC Option Slot
99-1* Hardware Control
99-11 RFI 2
99-12 Fan
99-1* Software Readouts
99-13 Idle time
99-14 Paramdb requests in queue
99-15 Secondary Timer at Inverter Fault
99-16 No. of Current Sensors
99-17 tCon1 time
99-18 tCon2 time
99-19 Time Optimize Measure
99-2* Heatsink Readouts
99-20 HS Temp. (PC1)
99-21 HS Temp. (PC2)
99-22 HS Temp. (PC3)
99-23 HS Temp. (PC4)
99-24 HS Temp. (PC5)
99-25 HS Temp. (PC6)
99-26 HS Temp. (PC7)
99-27 HS Temp. (PC8)
99-3* Performance Readouts
99-34 Perf FastThread AOC
99-35 Perf SlowThread AOC
99-36 Perf IdleThread AOC
99-37 Perf SystemIdleThread AOC
99-38 Perf CPU usage AOC (%)
99-39 Performance IntervalCounter
99-4* Software Control
99-40 StartupWizardState
99-41 Performance Measurements
99-5* PC Debug
99-50 PC Debug Selection
99-51 PC Debug 0
99-52 PC Debug 1
99-53 PC Debug 2
99-54 PC Debug 3
99-55 PC Debug 4
99-56 Fan 1 Feedback
99-57 Fan 2 Feedback
99-58 PC Auxiliary Temp
99-59 Power Card Temp.
99-8* RTDC
99-80 tCon1 Selection
99-81 tCon2 Selection
99-82 Trig Compare Selection
99-83 Trig Compare Operator
99-84 Trig Compare Operand
99-85 Trig Start
99-86 Pre-trigger
99-9* Internal Values
99-90 Options present
99-91 Motor Power Internal
99-92 Motor Voltage Internal
99-93 Motor Frequency Internal
600-** PROFIsafe
600-22 PROFIdrive/safe Tel. Selected
600-44 Fault Message Counter
600-47 Fault Number
600-52 Fault Situation Counter
601-** PROFIdrive 2
601-22 PROFIdrive Safety Channel Tel. No.
Appendix A - Parameters Installation Manual
MG37A322 Danfoss A/S © Rev. 04/2015 All rights reserved. 111
9 9
To Next Page
Loading...
Need help?
General