Need help?Do you have a question about the Dell EMC PowerVault ME4 Series and is the answer not in the manual?
Procedure for unpacking and identifying components of the ME4 Series storage system.
Essential safety instructions for installing and operating Dell EMC PowerVault ME4 Series Storage System.
Step-by-step guide for planning and successfully installing the ME4 Series enclosure system.
Guidance on system configuration requirements before initiating enclosure installation.
Details on supported disk drive modules, drive carriers, and DDICs for ME4 Series enclosures.
Guidelines for installing Disk Drive in Carrier (DDIC) modules into 5U84 enclosure drawers.
Information on using rack mounting rails for 19-inch rack cabinets with ME4 Series enclosures.
Instructions for physically installing the 2U enclosure into a rack cabinet using rail kits.
Procedure for installing the 5U84 enclosure into a rack cabinet, noting weight considerations.
Guidance on connecting additional expansion enclosures to the ME4 Series storage system.
Details on cable types and lengths required for connecting ME4 Series expansion enclosures.
Overview of methods and considerations for cabling ME4 Series controller enclosures to host servers.
Description of host interface protocols and common cabling configurations for ME4 Series.
Configuration details for Fibre Channel host connections using ME4 Series CNC ports.
Configuration details for iSCSI host connections using ME4 Series CNC ports.
Information on connecting SAS hosts using 12Gb/s interface protocol and qualified cables.
Procedure for connecting power cables from PCMs/PSUs to the PDU for the storage system.
Guidance on using the System Information Worksheet to document essential setup details.
Overview of the ME Storage Manager's guided setup for system configuration and provisioning.
Instructions for accessing the ME Storage Manager interface via web browser for system setup.
Procedure for updating controller modules, expansion modules, and disk drives firmware.
Details on configuring essential system settings, including network and notification parameters.
Steps to configure static or automatic IP addresses for controller network ports.
Instructions for configuring Fibre Channel (FC) ports on ME4 Series controller modules.
Instructions for configuring iSCSI ports on ME4 Series controller modules.
Guide to using the Storage Setup wizard for creating disk groups and pools.
Prerequisites for connecting host servers to ME4 Series controller enclosures.
Explanation of ALUA compliance and the need for multipath I/O (MPIO) configuration.
Ensuring HBAs, network adapters, BIOS, and firmware are installed and updated for Windows hosts.
Step-by-step guide for configuring Fibre Channel host servers running Windows Server.
Instructions for configuring iSCSI hosts on Windows Server using dual switch subnets.
Procedure for configuring SAS host servers running Windows Server, including MPIO setup.
Ensuring HBAs, network adapters, and BIOS are installed and updated for Linux hosts.
Guide for configuring Fibre Channel host servers running Linux.
Instructions for configuring iSCSI hosts on Linux systems using dual switch subnets.
Prerequisites for installing and configuring VMware ESXi operating system on hosts.
Steps to configure Fibre Channel host servers running VMware ESXi.
Procedure for configuring iSCSI host servers running VMware ESXi.
Guide for configuring SAS host servers running VMware ESXi.
Information on identifying the Service Tag and Express Service Code for ME4 Series storage systems.
Explanation of Ops panel LEDs for 2U and 5U enclosures to indicate system status.
Guidance on troubleshooting common initial start-up issues using LEDs and system status.
Common problems and alarm conditions for 2U enclosures and their resolutions.
Common problems and alarm conditions for 5U enclosures and their resolutions.
Basic methodology for locating faults within a storage system and identifying affected components.
Procedures for diagnosing and isolating faults in host-side connection to the storage system.
Overview of asynchronous block-level data replication between primary and secondary storage systems.
Details on using 10Gbase-T or CNC ports for replication and considerations for controller configurations.
Illustrative diagrams showing cabling configurations for replication between ME4 Series systems.
Identification and location of SFP+ transceivers shipped with the controller enclosure.
Step-by-step instructions for installing SFP+ transceivers into ME4 Series FC/iSCSI controller modules.
Worksheet for recording essential ME4 Series storage system network and administrator details.
Worksheet for planning and recording network information for the iSCSI network.
Procedure for manually setting IP addresses for controller ports via CLI or serial cable.
Details on connecting to the mini-USB port for console access on ME4 Series controller modules.
Information on required device drivers or special modes for operating systems connecting to the USB CLI port.
To Next Page
General