EasyManua.ls Logo

Delta Electronics ASDA-A Series - User Manual

Delta Electronics ASDA-A Series
383 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Call 1(800)985-6929 for Sales
deltaacdrives.com
sales@deltaacdrives.com
Call 1(800)985-6929 for Sales
deltaacdrives.com
sales@deltaacdrives.com

Table of Contents

Other manuals for Delta Electronics ASDA-A Series

Preview: Quick Start
Quick Start31 pages

Questions and Answers

  • W
    Wendy TuckerSep 7, 2025
    What to do if my Delta Electronics ASDA-A shows an overload error?
    • M
      Michelle LaneSep 7, 2025
      If your Delta Electronics Servo Drive is showing an overload error, it means the drive has exceeded its rated load during continuous operation. You can increase the motor capacity or reduce the load. It could also be due to a defective control system parameter setting, so adjust the gain value of the control circuit. If the accel/decel setting time is too fast, decrease it. Also, verify that the wiring of the motor and position detector is correct.
  • J
    Jeffrey DurhamAug 22, 2025
    What causes an undervoltage error on a Delta Electronics Servo Drive?
    • R
      royjeffersonAug 22, 2025
      An undervoltage error on your Delta Electronics Servo Drive can be caused by several factors. The main circuit voltage might be below its minimum specified value, so reconfirm the voltage wiring. There might be no input voltage at the main circuit, so reconfirm the power switch. Lastly, an incorrect power input could be the issue; use the correct power supply or a serial stabilizer.
  • J
    Jeffrey ThompsonSep 4, 2025
    What to do if my Delta Electronics Servo Drive shows an overcurrent error?
    • S
      sgreenSep 5, 2025
      If your Delta Electronics Servo Drive displays an overcurrent error, there could be several reasons. It could be due to a short-circuit at the drive output, in which case you should repair the short circuit and ensure no metal conductors are exposed. Another cause might be a motor wiring error, so double-check the wiring according to the user manual. An IGBT error may also be the cause, in which case you should return the drive to the distributor or manufacturer. A control parameter setting error can also cause this problem. Try setting the drive back to factory default settings and then carefully readjust the parameters. Finally, a control command setting error may be the reason. Ensure that the input command frequency is stable and activate the filter function.
  • M
    munozkimSep 3, 2025
    What causes a DSP communication error in Delta Electronics ASDA-A?
    • D
      David JacksonSep 3, 2025
      A DSP communication error in Delta Electronics Servo Drives is caused by a control power error. If the error does not clear after resetting the power supply, contact the distributor for assistance or return to manufacturer.
  • A
    Aaron HorneSep 2, 2025
    What causes a memory error in Delta Electronics Servo Drives?
    • B
      brandi72Sep 2, 2025
      A memory error in Delta Electronics Servo Drives indicates a data read-out/write-in error in the memory. If the error does not clear after resetting the parameter or power supply, contact the distributor for assistance or return to manufacturer.
  • T
    Tyler LopezSep 1, 2025
    What causes a command write-in error on a Delta Electronics Servo Drive?
    • C
      Carmen AllenSep 1, 2025
      A command write-in error on a Delta Electronics Servo Drive is caused by a control power supply error. If the error does not clear after resetting the power supply, contact the distributor for assistance or return to manufacturer.
  • M
    Maria CastroAug 30, 2025
    What to do if my Delta Electronics Servo Drive displays 'watch dog execution time out'?
    • D
      Denise DunnAug 30, 2025
      If your Delta Electronics Servo Drive displays 'watch dog execution time out', it indicates a watch dog execution error. If there are any abnormal conditions after resetting the power supply, return it to the distributor or manufacturer.
  • R
    randallvictoriaAug 29, 2025
    What causes a serial communication time out on a Delta Electronics Servo Drive?
    • D
      davisbryanAug 29, 2025
      A serial communication timeout on a Delta Electronics Servo Drive can occur if the setting value in the timeout parameter is incorrect, so ensure the setting value is correct. It can also happen if the drive isn't receiving a communication command for a long time, so make sure to perform wiring correctly.
  • M
    Michael MendozaAug 27, 2025
    What to do if my Delta Electronics Servo Drive shows an adjustment error?
    • R
      Ronald ParkerAug 28, 2025
      If your Delta Electronics Servo Drive shows an adjustment error, it could be because the analog input contact does not correctly return to zero. Correctly ground the analog input contact. If the error persists after resetting the power supply, the detection device may be damaged, contact the distributor for assistance or return to manufacturer.
  • S
    sgordonAug 27, 2025
    What causes a serial communication error in Delta Electronics ASDA-A Servo Drives?
    • S
      Sonya GravesAug 27, 2025
      A serial communication error in Delta Electronics Servo Drives can stem from several issues. The communication parameter setting might not be correct, so ensure the parameter setting value is set correctly. Also, the communication address might be incorrect, so make sure the communication address is set correctly. Finally, the communication setting value might be incorrect, so verify that the communication setting value is correct.

Delta Electronics ASDA-A Series Specifications

General IconGeneral
SeriesASDA-A
CategoryServo Drives
Control ModesPosition, Speed, Torque
FeedbackIncremental encoder, Absolute encoder
Protection ClassIP20
Communication InterfaceRS-485
Protection FeaturesOver-voltage, Over-current, Overtemperature
Operating Temperature0°C to 50°C
Storage Temperature-20°C to 65°C
Shock Resistance11ms

Related product manuals