Denon AVR-1612 Owner's Manual

14
STEP 4
Calculate
Set up speakers (Audyssey
®
Auto Setup)
•In STEP 3, you will perform measurements at multiple positions (two
to six positions) other than the main listening position.
•Just one position can be measured but measuring multiple positions
increases the accuracy of the correction of acoustic distortion within
the listening area.
10
Move the setup microphone to
position 2, use ui to select
“Measure”, and then press
ENTER.
The measurement of the second
position starts. Measurements can be
made in up to six positions.
Audyssey Auto Setup MultEQ
Measure (2nd)
Please place the
microphone at ear
height at 2nd
listening position.
Measure
Next Calculate
[RETURN][ENTER] Enter Cancel
If you want to omit measurements from the next position onward,
select “Next Calculate”.
(Go to
STEP4 Calculate
)
11
Repeat step 10, measuring positions 3 to 6.
When measurement of position 6 is completed, a
“Measurements finished.” message is displayed.
Audyssey Auto Setup MultEQ
Measure (Finish)
Measurements finished.
Next Calculate
Retry
[RETURN][ENTER] Enter Cancel
12
On the
STEP 3
screen, use ui to select “Next →
Calculate”, and then press ENTER.
Measuring results are analyzed, and the frequency response of
each speaker in the listening room is determined.
Audyssey Auto Setup MultEQ
Calculate
Now calculating
Please wait
0%
•Analysis takes several minutes to complete. The time required for
this analysis depends on the number of speakers connected.
The more connected speakers there are, the longer it takes to
perform analysis.
STEP 3
Measure (2nd – 6th)
STEP 2 (Continued)
Detect & Measure (Main)
NOTE
If “Caution” is displayed:
Go to “Error messages” (vpage 16),
check any related items, and perform the
necessary procedures.
If the problem is resolved, return and restart
“Audyssey
®
Auto Setup”.
When performing Audyssey
®
Auto Setup over
again
Press ui to select “Retry”, and then press ENTER.
When measuring has stopped
q Press RETURN B, to the “Cancel Auto Setup?” prompt is
displayed.
w Press o to select “Yes”, then press ENTER.
Setting up the speakers again
Repeat the operation from step 4 of
STEP 1 Preparation
.
Basic version
Advanced version
Information
Basic version
vSee overleaf

Denon AVR-1612 Specifications

General

Audio output channels	5.1 channels
Audio A/D Converter (ADC)	24-bit/96kHz
Power output per channel (1KHz@6 Ohm)	120 W
Power output per channel (20-20KHz@8 Ohm)	80 W
HDMI in	4
Composite video in	3
S-Video inputs quantity	1
Speakers connectivity type	-
Ethernet LAN	No
Radio Data System (RDS)	Yes
Preset stations quantity	56
Analog signal format system	NTSC, PAL
Display	LCD
HDMI version	1.4
Product color	Black
Audio decoders	Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS 96/24, DTS Neo:6, DTS-ES, DTS-HD
Apple docking compatibility	iPod
Graphical user interface (GUI) language	English, French, German
AC input voltage	220-240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.5 W
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 80 %

Weight and Dimensions

Depth	382 mm
Width	435 mm
Height	162 mm
Weight	9200 g