EasyManuals Logo

Denon AVR-1905 User Manual

Denon AVR-1905
77 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #39 background imageLoading...
Page #39 background image
Set the external input (EXT.
IN) mode.
Press the EXT. IN button to
switch the external input.
Once this is selected, the input signals connected to the FL
(front left), FR (front right), C (center), SL (surround left) and
SR (surround right) channels of the EXT. IN jacks are output
directly to the front (left and right), center and surround (left
and right) speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer) jack is
output to the PRE OUT SUBWOOFER jack.
1
EXT. IN
2
Cancelling the external input mode
To cancel the external input (EXT. IN) setting, press the INPUT
MODE (AUTO, PCM, DTS) or ANALOG button to switch to
the desired input mode. (See page 37.)
INPUT MODE
ANALOG
When the input mode is set to the external input (EXT. IN), the play
mode (DIRECT, STEREO, STANDARD (DOLBY/DTS SURROUND),
5CH/7CH STEREO or DSP SIMULATION) cannot be selected.
NOTES:
In play modes other than the external input mode, the signals
connected to EXT. IN jacks cannot be played. In addition, signals
cannot be output from channels not connected to the input
jacks.
The external input mode can be set for any input source. To
watch video while listening to sound, select the input source to
which the video signal is connected, then set this mode.
If the subwoofer output level seems to high, set the “SW ATT.”
surround parameter to “ON”.
Playback using the external input (EXT. IN) jacks
2 1
21
(Main unit) (Remote control unit)
(Main unit) (Remote control unit)
Playing audio sources (CDs and DVDs)
The AVR-1905/785 is equipped with two 2-channel playback modes exclusively for music.
Select the mode to suit your tastes.
1
DIRECT mode
Use this mode to achieve good quality 2-
channel sound while watching images. In
this mode, the audio signals bypass such
circuits as the tone circuit and are
transmitted directly, resulting in good
quality sound.
2
STEREO mode
Use this mode to adjust the tone and
achieve the desired sound while watching
images.
2
1
(Remote control unit)
1, 2
(Remote control unit)
DIRECT /
STEREO
(Main unit)
DIRECT /
STEREO
(Main unit)
39
ENGLISH

Other manuals for Denon AVR-1905

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-1905 and is the answer not in the manual?

Denon AVR-1905 Specifications

General IconGeneral
Speakers connectivity type-
Receiver typeSurround
Frequency range10 - 100000 Hz
Audio output channels7.1 channels
Signal-to-Noise Ratio (SNR)100 dB
Power output per channel (1KHz@6 Ohm)110 W
Power output per channel (20-20KHz@8 Ohm)80 W
Product colorBlack
Audio decodersDTS 96/24, DTS Neo:6, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), Dolby Digital EX, Dolby Pro Logic IIx
Digital Signal Processing (DSP)Yes
HDMI in0
Composite video in4
Digital audio coaxial in1
Component video (YPbPr/YCbCr) in3
S-Video outputs quantity2
Ethernet LANNo
AM band range520 - 1710 kHz
FM band range87.5 - 107.9 MHz
Supported radio bandsAM, FM
AC input voltage120 V
AC input frequency60 Hz
Weight and Dimensions IconWeight and Dimensions
Depth171 mm
Width434 mm
Height416 mm
Weight11900 g

Related product manuals