What does 'Overcurrent' mean on Denon AVR-1911 Stereo Receiver?
If your Denon Stereo Receiver displays 'Overcurrent', the USB device is using too much power. If it's a portable hard disk with an AC adapter, connect the adapter.
How to fix Denon Stereo Receiver when power does not turn on?
If your Denon Stereo Receiver isn't powering on, ensure the power plug is fully inserted into the outlet. If it still doesn't turn on, the protection circuit might be active. Unplug the receiver, wait 5-10 seconds, and then plug it back in.
How to troubleshoot no sound from subwoofer on Denon Stereo Receiver?
If your subwoofer isn't producing sound with your Denon Stereo Receiver: * Check the subwoofer connections. * Ensure the subwoofer is powered on. * In the menu, set “Speaker Config.” – “Subwoofer” to “Yes`. * If “Front” and “Center” for “Speaker Config.” are set to “Large”, and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected surround mode.
Why is there no audio output with HDMI connection on Denon Stereo Receiver?
If you're not getting audio with an HDMI connection on your Denon Stereo Receiver: * Check the HDMI connector connections. * To output audio from the speakers, set “HDMI Audio Out” to “Amp` in the menu. * To output audio from the TV, set “HDMI Audio Out” to “TV` in the menu.
How to enable surround back speaker on Denon AVR-1911 Stereo Receiver?
If there's no sound from the surround back speaker on your Denon Stereo Receiver: * Set “Amp Assign” to “Normal` in the menu. * Set “Speaker Config.” – “S.Back” to something other than “None`. * Set “Surround Parameter” – “S.Back” to something other than “OFF`. * Ensure the surround mode is not set to “STEREO`.
Why are file names not displayed properly on Denon AVR-1911?
If file names are not displaying correctly (“...”, etc.) on your Denon Stereo Receiver, this unit replaces characters it cannot display with a period (“.”).
How to enable DTS sound output on Denon AVR-1911?
If DTS sound isn't outputting on your Denon Stereo Receiver, set “Decode Mode” in the menu to either “Auto” or “DTS`.
How to turn on display on Denon AVR-1911 Stereo Receiver?
If the display on your Denon Stereo Receiver is off, go to the menu and set “Display” to something other than “OFF”.
What does it mean when the power indicator is blinking red in intervals of approximately 2 seconds on Denon AVR-1911?
If the power indicator on your Denon Stereo Receiver blinks red every 2 seconds, the unit's internal temperature has risen. Turn off the power and allow the unit to cool down before turning it back on. Also, ensure the unit is installed in a well-ventilated area.
How to improve reception on Denon AVR-1911?
If you're experiencing poor reception, noise, or distortion with your Denon Stereo Receiver, try these steps: * Adjust the antenna's orientation or position. * Separate the AM loop antenna from the unit. * Consider using an FM outdoor antenna. * Keep the antenna separate from other connection cables.
Important warnings and guidelines for safe operation and moving the unit.
Procedures for physically installing and connecting speakers to the unit.
Steps to power on the unit and initiate the automatic speaker setup process.
Detailed steps for microphone placement, subwoofer setup, and remote control configuration.
Detailed steps for connecting devices via HDMI, including functions and cable requirements.
Guide for setting up speaker configurations beyond the standard 5.1 system.
Detailed audio adjustments and manual configuration of speaker, HDMI, and audio settings.
General| Frequency range | 10 - 100000 Hz |
|---|---|
| Audio output channels | 7.1 channels |
| Audio A/D Converter (ADC) | 24-bit/96kHz |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Total Harmonic Distortion (THD) | 0.8 % |
| HDMI | Yes |
| Audio system | Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, DTS-HD, DTS 96/24 |
| Output power | 125 W |
| Dimensions (WxDxH) | 434 x 381 x 171 mm |
| Power requirements | AC 230, 50 Hz |
| HDMI ports quantity | 5 |
| AM band range | 522 - 1611 kHz |
| FM band range | 87.5 - 108 MHz |
| I/O ports | 1 x Component in 1 x Composite Monitor out 1 x USB 1 x Microphone 1 x FM Tuner Antenna 1 x AM Tuner Antenna |
| Connectivity technology | Wired |
| Headphone outputs | 7 |
| Digital audio optical in | 1 |
| Product color | Black |
| Power consumption (standby) | 0.1 W |
| Power consumption (typical) | 460 W |
Weight and Dimensions| Weight | 10200 g |
|---|
To Next Page
