To Next PageTo Next PageWhy can't I play files on a USB memory device with my Denon Stereo Receiver?
If your Denon Stereo Receiver isn't playing files from a USB device: * Format the USB device to “FAT16” or “FAT32”. * If the USB is partitioned, only the top partition's files can be played. * The file may be in an incompatible format; use a compatible format. * The unit cannot play back copyright-protected files.
What to do if audio is not output from Denon AVR-1911 Stereo Receiver?
If there's no sound coming from your Denon Stereo Receiver, try these steps: * Check all device connections and speaker connections. * Ensure the audio device is powered on. * Adjust the master volume and cancel mute mode. * Select the correct input source and mode. * Disconnect headphones, as this may disable speaker output.
Why is there no video output with HDMI connection on Denon Stereo Receiver?
If you're not getting video output via HDMI from your Denon Stereo Receiver: * Check the HDMI connector connections. * Ensure the input source matches the connected HDMI connector. * Verify that your TV is compatible with HDCP (copyright protection). Incompatible devices may prevent correct video output.
How to improve reception on Denon AVR-1911?
If you're experiencing poor reception, noise, or distortion with your Denon Stereo Receiver, try these steps: * Adjust the antenna's orientation or position. * Separate the AM loop antenna from the unit. * Consider using an FM outdoor antenna. * Keep the antenna separate from other connection cables.
Why is the power indicator is blinking red in intervals of approximately 0.5 seconds on Denon Stereo Receiver?
If the power indicator on your Denon Stereo Receiver is blinking red every 0.5 seconds, ensure you are using speakers with the correct impedance. Also, check the speaker cables for any shorts (touching wires). Twist the core wire firmly and reconnect to the speaker terminal.
What to do if no picture appears from Denon AVR-1911 Stereo Receiver?
If you're not getting a picture on your TV from the Denon Stereo Receiver, first check the TV connection. Then, make sure you have selected the correct TV input.
Why the Denon Stereo Receiver cannot be operated with the remote control unit?
If your Denon Stereo Receiver isn't responding to the remote, try these solutions: * Replace the remote batteries with new ones. * Ensure you're within 7 meters and 30° of the unit. * Remove any obstacles blocking the remote sensor. * Verify the batteries are inserted correctly (+/-). * Move the unit away from strong light sources like direct sunlight or inverter-type fluorescent lights.
How do I fix no sound from front height speaker on Denon AVR-1911 Stereo Receiver?
If you're not getting sound from the front height speakers on your Denon Stereo Receiver: * Set “Surround Parameter” – “Front Height” to “ON` in the menu. * Set “Amp Assign” to “Front Height` in the menu. * Set “Speaker Config.” – “Surround” to something other than “None`.
How to enable surround back speaker on Denon AVR-1911 Stereo Receiver?
If there's no sound from the surround back speaker on your Denon Stereo Receiver: * Set “Amp Assign” to “Normal` in the menu. * Set “Speaker Config.” – “S.Back” to something other than “None`. * Set “Surround Parameter” – “S.Back” to something other than “OFF`. * Ensure the surround mode is not set to “STEREO`.
Why is there no audio output with HDMI connection on Denon Stereo Receiver?
If you're not getting audio with an HDMI connection on your Denon Stereo Receiver: * Check the HDMI connector connections. * To output audio from the speakers, set “HDMI Audio Out” to “Amp` in the menu. * To output audio from the TV, set “HDMI Audio Out” to “TV` in the menu.
General| Frequency range | 10 - 100000 Hz |
|---|---|
| Audio output channels | 7.1 channels |
| Audio A/D Converter (ADC) | 24-bit/96kHz |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Total Harmonic Distortion (THD) | 0.8 % |
| HDMI | Yes |
| Audio system | Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, DTS-HD, DTS 96/24 |
| Output power | 125 W |
| Dimensions (WxDxH) | 434 x 381 x 171 mm |
| Power requirements | AC 230, 50 Hz |
| HDMI ports quantity | 5 |
| AM band range | 522 - 1611 kHz |
| FM band range | 87.5 - 108 MHz |
| I/O ports | 1 x Component in 1 x Composite Monitor out 1 x USB 1 x Microphone 1 x FM Tuner Antenna 1 x AM Tuner Antenna |
| Connectivity technology | Wired |
| Headphone outputs | 7 |
| Digital audio optical in | 1 |
| Product color | Black |
| Power consumption (standby) | 0.1 W |
| Power consumption (typical) | 460 W |
Weight and Dimensions| Weight | 10200 g |
|---|
Important warnings and guidelines for safe operation and moving the unit.
Procedures for physically installing and connecting speakers to the unit.
Steps to power on the unit and initiate the automatic speaker setup process.
Detailed steps for microphone placement, subwoofer setup, and remote control configuration.
Detailed steps for connecting devices via HDMI, including functions and cable requirements.
Guide for setting up speaker configurations beyond the standard 5.1 system.
Detailed audio adjustments and manual configuration of speaker, HDMI, and audio settings.
