EasyManuals Logo

Denon AVR-1911 User Manual

Denon AVR-1911
88 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #41 background imageLoading...
Page #41 background image
37
ENGLISH
Basic versionSimple version InformationAdvanced version
Convenient functions
Sleep timer function
The power automatically goes into standby once the set time has
elapsed.
This is convenient for playing sources while going to sleep.
Press SLEEP and display the time you
want to set.
The “SLEEP” indicator on the display lights.
The time switches as shown below each
time SLEEP is pressed.
OFF 10 min 20 30 40 50
6080 7090100
110
120
To cancel the sleep timer
Press SLEEP to set “OFF”.
The “SLEEP” indicator on the display turns off.
The sleep timer setting is canceled if this unit’s power is set to
standby or turned off.
When power to the main zone is turned off with the sleep timer,
power in ZONE2 is also turned off.
Adjusting the volume of the speakers
You can adjust the channel level either according to the playback
sources or to your taste, as described below.
n Adjusting the volume of the different speakers
1
Press ZONE SELECT to switch the
zone mode to “MAIN”.
The “MAIN” indicator lights.
2
Press AMP to set the remote
control unit to amplier
operation mode.
3
Press CH LEVEL.
Channel Level
C 0.0dB SBR 0.0dB
FL 0.0dB SR 0.0dB
[ ]:CH Sel.
FR 0.0dB SBL 0.0dB
SW 0.0dB SL 0.0dB
Fader
FRONT : REAR
4
Use ui to select the speaker.
The speaker that can be set switches
each time one of the buttons is pressed.
5
Use o p to adjust the volume.
In the case of a subwoofer, pressing o when it is at “–12 dB” will
change the setting to “OFF”.
When a headphone jack is inserted, the headphone channel level can
be adjusted.
n Adjusting the volume of groups of speakers
(Fader function)
This function lets you adjust (fade) the sound all at once from the
front (front speaker / front height speaker / center speaker) or rear
(surround speaker / surround back speaker).
1
Press ZONE SELECT to switch the
zone mode to “MAIN”.
The “MAIN” indicator lights.
2
Press AMP to set the remote
control unit to amplier
operation mode.
3
Press CH LEVEL.
Channel Level
C 0.0dB SBR 0.0dB
[ ]:CH Sel.
FR 0.0dB SBL 0.0dB
SW 0.0dB SL 0.0dB
FRONT : REAR
FL 0.0dB SR 0.0dB
Fader
4
Use i to select “Fader”, then
select the item to be adjusting
using o p.
5
Use o p to adjust the volume of the speakers.
(o : front, p: rear)
The fader function does not affect the subwoofer.
The fader can be adjusted until the volume of the speaker is adjusted
to the lowest value of -12 dB.

Table of Contents

Other manuals for Denon AVR-1911

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-1911 and is the answer not in the manual?

Denon AVR-1911 Specifications

General IconGeneral
Frequency range10 - 100000 Hz
Audio output channels7.1 channels
Audio A/D Converter (ADC)24-bit/96kHz
Signal-to-Noise Ratio (SNR)100 dB
Total Harmonic Distortion (THD)0.8 %
HDMIYes
Audio systemDolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, DTS-HD, DTS 96/24
Output power125 W
Dimensions (WxDxH)434 x 381 x 171 mm
Power requirementsAC 230, 50 Hz
HDMI ports quantity5
AM band range522 - 1611 kHz
FM band range87.5 - 108 MHz
I/O ports1 x Component in 1 x Composite Monitor out 1 x USB 1 x Microphone 1 x FM Tuner Antenna 1 x AM Tuner Antenna
Connectivity technologyWired
Headphone outputs7
Digital audio optical in1
Product colorBlack
Power consumption (standby)0.1 W
Power consumption (typical)460 W
Weight and Dimensions IconWeight and Dimensions
Weight10200 g

Related product manuals