88
ENGLISH
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Conļ¬rm the setting Return to previous menu
Manual Setup
Setting items Setting details
GUI
(Continued)
TUNER : Set the tuner screen display time when the input source is
āSIRIUSā or āHD Radioā.
ā¢ Always : Show display continuously.
ā¢ 30sec : Show display for 30 seconds after operation.
ā¢ 10sec : Show display for 10 seconds after operation.
ā¢ OFF : Turn display off.
iPod : Set the iPod screen display time when the input source is āDOCKā
or āiPod (USB)ā.
ā¢ Always : Show display continuously.
ā¢ 30sec : Show display for 30 seconds after operation.
ā¢ 10sec : Show display for 10 seconds after operation.
ā¢ OFF : Turn display off.
Remote Preset Codes
Search a preset code to
register in the remote
control unit.
See āRegistering preset codesā (vpageī91).
Quick Select Name
Change the āQuick Selectā
display title to one you
prefer.
ā¢ Up to 16 characters can be input.
ā¢ For character input, see page 65.
Zone Rename
Change the display title of
each zone to one you prefer.
ā¢ Up to 10 characters can be input.
ā¢ For character input, see page 65.
Trigger Out
Select the condition for
activating Trigger Out 1/2 for
the input source, surround
mode, etc.
See āTRIGGER OUT jacksā
(vpageī23) for more
information on trigger out.
Trigger Out 1 / Trigger Out 2
n When setting for zone (MAIN ZONE / ZONE2 / ZONE3)
Trigger out is activated through linkage to the power of the zone set
to āONā.
n When setting for input source
Activate trigger out when the input source set to āONā is selected.
Active for the zone set to āONā with āWhen Setting for Zoneā.
n When setting for surround mode
Activate trigger out when the surround mode set to āONā is selected.
Active when the āMAIN ZONEā set to āONā with āWhen Setting
for Zoneā is selected, and when the input source set to āONā with
āWhen Setting for Input Sourceā is selected.
n When setting for HDMI monitor
Activate trigger out when the HDMI monitor set to āONā is selected.
Activate trigger out when the HDMI monitor set to āONā is
selected. Active when the āMAIN ZONEā set to āONā with
āWhen Setting for Zoneā is selected, and when the input source
set to āONā with āWhen Setting for Input Sourceā is selected.
ā¢ ON : Activate trigger on this mode.
ā¢ ā ā ā : Do not activate trigger on this mode.
Setting items Setting details
Trigger Out
(Continued)
Default : The āTrigger Outā settings are returned to the default settings.
ā¢ Yes : Reset to the defaults.
ā¢ No : Do not reset to the defaults.
Remote ID Setup
Set when you operate
another DENON AV
ampliļ¬er with the remote
control unit of this unit.
Match the remote control
unit you are using with the
remote ID of this unit.
1 / 2 / 3 / 4
NOTE
When using this unit with only the included main remote control unit (RC-
1146), use Remote ID ā1ā (default).
When using the included sub remote control unit (RC-1148), this function
can be used. Match the ID setting of the remote control unit and the
receiver.
Dimmer
Adjust the display
brightness of this unit.
Bright : Normal display brightness.
Dim : Reduced display brightness.
Dark : Very low display brightness.
OFF : Turns the display off.
Setup Lock
Protect settings from
inadvertent change.
ON : Turn protection on.
OFF : Turn protection off.
When canceling the setting, set āSetup Lockā to āOFFā.
NOTE
When āSetup Lockā is set to āONā, the settings listed below can no
longer be changed. Also, āSETUP LOCKED!ā is displayed if you attempt
to operate related settings.
Ā· Menu operations Ā· Channel Level
Ā· RESTORER Ā· MultEQ
Ā®
XT
Ā· Dynamic Volumeā¢ Ā· Dynamic EQ
Ā®
Maintenance Mode
Use when receiving
maintenance from a DENON
service engineer or custom
installer.
NOTE
Only use this function if so instructed by a DENON serviceperson or
installer.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
