EasyManuals Logo

Denon AVR-590 User Manual

Denon AVR-590
74 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #37 background imageLoading...
Page #37 background image

ENGLISH
Getting Started
Connections Remote Control Information Troubleshooting
SpecificationsSettings
Playback
Playing Components
1
Prepare for playback.
①Turn on the power of the TV, subwoofer
and player.
②Set the TV’s input to the AVR-590.
③Load the disc in the player.
2
Turn on the AVR-590’s power.
(vpage 16“Turning the Power On”)
3
Press and select the input
source.
If “TUNING PRESET” is selected for preset
channel, press before turning .
4
Play the component connected to the AVR-590.
Make the necessary settings on the player (language
setting, subtitles setting, etc.) beforehand.
5
Use to adjust the volume.
GVariable rangeH
– – –
–80.0dB ~ 18.0dB
※The variable range differs according to the input signal and channel
level setting.
6
Select the desired surround mode.
(vpage 37“Selecting the Surround Mode”)
7
Adjust the desired sound eld effects.
(vpage 39Adjusting the Sound Field Effects”)
The following describes the procedure for playing Blu-ray disc/
DVD players.
Use the same procedure to play other components.
Playing Blu-ray Disc / DVD Players
The music / video on an iPod can be played by using the control
dock for iPod (ASD-1R, ASD-11R, ASD-3N or ASD-3W sold
separately).
Connect the control dock for iPod beforehand. (vpage 14
“iPod
®
”).
iPod
®
Playback
1
Prepare for playback.
q Set the iPod in the DENON control
dock for iPod.
w Assign the control dock for iPod’s input
(vpage 31).
eSwitch to “DEVICE”.
2
Turn on the AVR-590’s power.
(vpage 16“Turning the Power On”)
3
Press to select the input
source assigned in step 1-w
above.
b If the screens above are not
displayed, the iPod may not be
properly connected. Try connecting
again.
(iPod screen)
Listening to music on an iPod
®
OK to disconnect.
Adjusting the Sound Field Effects (Parameter)
(vpage 39)
Playing Components (vpage 34)
n Playing Blu-ray Disc/DVD Players (vpage 34)
n iPod® Playback (vpage 34)
n Listening to FM/AM Broadcasts (vpage 36)
n Operations During Playback (vpage 37)
n Operation Flow
Before starting playback, make the connections between the
different components and the settings on the receiver.
Selecting the Surround Mode (vpage 37)
q Standard Playback (vpage 37)
w Playing in a DENON original surround mode
(vpage 38)
e Direct Playback (vpage 38)
r Stereo Playback (vpage 39)
NOTE
●Also refer to the operating instructions of the connected
components when playing them.
External devices can be controlled by remote control unit
(vpage 46 Operating the Connected Devices by Remote
Control Unit”).
See overleaf
Playback

Table of Contents

Other manuals for Denon AVR-590

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-590 and is the answer not in the manual?

Denon AVR-590 Specifications

General IconGeneral
Number of Channels5.1
HDMI Inputs3
HDMI Outputs1
Response Bandwidth10 Hz - 100 kHz
Signal-To-Noise Ratio98 dB
THD0.08%
Input Impedance47 kOhm
Input Sensitivity200 mV
Tuner TypeDigital
Tuner BandsAM/FM
Preset Station Qty56
Surround System Class5.1 channel
HDMI SwitchingYes
Width434 mm
Frequency Response10 Hz - 100 kHz
Dolby TechnologiesDolby Digital, Dolby Digital Plus, Dolby Pro Logic II
DTS TechnologiesDTS 96/24, DTS Neo:6
Audio D/A Converter24-bit / 192kHz
Tuner Frequency RangeFM: 87.5-108 MHz, AM: 522-1611 kHz

Related product manuals