EasyManuals Logo

Denon AVR-590 User Manual

Denon AVR-590
74 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #39 background imageLoading...
Page #39 background image

ENGLISH
Getting Started
Connections Remote Control Information Troubleshooting
SpecificationsSettings
1
Tune in the broadcast station you want to preset.
2
Press .
3
Press
to select the block (A to G)
in which the station is to be preset.
4
Press to select the preset number (1 to 8).
5
Press again to complete the setting.
To preset other stations, repeat steps 1 to 5.
Stations can be preset automatically at menu Auto Preset” (vpage
33).
NOTE
Preset stations are erased by overwriting them.
If the desired station cannot be tuned in with auto tuning, tune it in
manually.
When tuning in stations manually, press and hold to change
frequencies continuously.
The time (default : 30 sec) for which the on-screen display are
displayed can be set at On-Screen Display” (vpage 29).
Presetting Radio Stations (Preset Memory)
Your favorite broadcast stations can be preset so that you can tune
them in easily. Up to 56 stations can be preset.
Playing Components
1
Press to select the memory block (A to G).
2
Press to select the desired preset channel (1 to
8).
n Default settings
Auto tuner presets
A1 ~ A8
87.5 / 89.1 / 98.1 / 107.9 / 90.1 / 90.1 / 90.1 /
90.1 MHz
B1 ~ B8
520 / 600 / 1000 / 1400 / 1500 / 1710 kHz,
90.1 / 90.1 MHz
C1 ~ C8
90.1 MHz
D1 ~ D8
90.1 MHz
E1 ~ E8
90.1 MHz
F1 ~ F8
90.1 MHz
G1 ~ G8
90.1 MHz
Listening to Preset Stations
Playback
1
Set to “TUNER/AMP”.
2
Press to select “TUNER”.
3
Press to select “FM” or “AM”.
4
Tune in the desired broadcast
station.
q To tune in automatically (Auto Tuning)
Press to light the “AUTO” indicator on
the display, then use to select the
station you want to hear.
w To tune in manually (Manual Tuning)
Press to turn off the display’s “AUTO” indicator, then use
to select the station you want to hear.
Listening to FM/AM Broadcasts
Basic Operation
You can also operate via the main unit. In this
case, perform the following operations.
Press , then turn on the main
unit to select the preset radio channel.

Table of Contents

Other manuals for Denon AVR-590

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-590 and is the answer not in the manual?

Denon AVR-590 Specifications

General IconGeneral
Number of Channels5.1
HDMI Inputs3
HDMI Outputs1
Response Bandwidth10 Hz - 100 kHz
Signal-To-Noise Ratio98 dB
THD0.08%
Input Impedance47 kOhm
Input Sensitivity200 mV
Tuner TypeDigital
Tuner BandsAM/FM
Preset Station Qty56
Surround System Class5.1 channel
HDMI SwitchingYes
Width434 mm
Frequency Response10 Hz - 100 kHz
Dolby TechnologiesDolby Digital, Dolby Digital Plus, Dolby Pro Logic II
DTS TechnologiesDTS 96/24, DTS Neo:6
Audio D/A Converter24-bit / 192kHz
Tuner Frequency RangeFM: 87.5-108 MHz, AM: 522-1611 kHz

Related product manuals