EasyManua.ls Logo

Denon DN-700C

Denon DN-700C
25 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
DN-700C/DN-501C
MIDI Command Guide
11
4-2. Device operation
Command
Category Code
Command
Example
Example Command Code * Red points are variable
Remark
[POWER ON] 1 1 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x01,0x00,0x31,0x34,0xF7
[POWER STANDBY] 1 2 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x02,0x00,0x31,0x35,0xF7
[RETRACT] 1 3 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x03,0x00,0x31,0x36,0xF7
[EJECT] 1 4 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x04,0x00,0x31,0x37,0xF7
[UNBAL VOL UP 10] 1 5 Volume up 0.1 dB 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x05,0x02,0x30,0x31,0x37,0x42,0xF7 * 1
Volume up 1.0 dB 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x05,0x02,0x30,0x41,0x38,0x42,0xF7
[UNBAL VOL DN 10] 1 6 Volume down 0.1 dB 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x06,0x02,0x30,0x31,0x37,0x43,0xF7 * 1
Volume down 1.0 dB 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x06,0x02,0x30,0x41,0x38,0x43,0xF7
[UNBAL VOL -123] 1 7 Volume -12.3dB
0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x07,0x04,0x01,0x31,0x32,0x33,0x42,
0x35,0xF7
* 2
Volume +10.0dB
0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x07,0x04,0x00,0x31,0x30,0x30,0x41,
0x46,0xF7
[ENTER] 1 8 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x08,0x00,0x31,0x42,0xF7
[ESC] 1 9 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x09,0x00,0x31,0x43,0xF7
[ABORT] 1 10 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x0A,0x00,0x31,0x44,0xF7
[ARROW D] 1 11 Arrow down 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x0B,0x00,0x31,0x45,0xF7
[ARROW U] 1 12 Arrow up 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x0C,0x00,0x31,0x46,0xF7
[ARROW R] 1 13 Arrow right 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x0D,0x00,0x32,0x30,0xF7
[ARROW L] 1 14 Arrow left 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x01,0x0E,0x00,0x32,0x31,0xF7
* 1 The parameter and checksum (written in red) are variable. The parameter should be “00” to “FF” (hexadecimal) in ASCII (e.g., 1.0dB = “0A”, 1.6dB = “10”).
* 2 The parameter and checksum (written in red) are variable. The parameter should be as below:
Byte 1: 0:Plus / 1:Minus
Byte2 to Byte5: 10 times the value of the volume in ASCII (+1.23 is 0x00,0x31,0x32,0x33)

Other manuals for Denon DN-700C

Related product manuals