Denon DN-700C

DN-700C/DN-501C
MIDI Command Guide
17
4-5. Device setting
Command Category Code Command Example Example Command Code * Red points are variable Remark
[DIMMER XXX] 7 1 Dimmer 100% 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x01,0x01,0x01,0x31,0x43,0xF7
Dimmer 75% 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x01,0x01,0x02,0x31,0x44,0xF7
Dimmer 50% 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x01,0x01,0x03,0x31,0x45,0xF7
Dimmer 25% 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x01,0x01,0x04,0x31,0x46,0xF7
Dimmer 0% 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x01,0x01,0x05,0x32,0x30,0xF7
[LOCK XXX] 7 2 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x02,0x01,0x01,0x31,0x44,0xF7
[PRESET X: Y]
7 3
Shift Mde= LOCK
0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x03,0x06,0x30,0x30,0x30,0x30,0x30,0x30,0x34,
0x32,0xF7
* 1
[PRESET ALL CHG ] 7 4 (All 1) 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x04,0x30,0x30,0x31,0x30,0x31,0x30,0x31,0x30,
0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x31,
0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,
0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x36,0x35,0xF7
* 1
[PRESET DEFAULT 7 5 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x05,0x00,0x31,0x45,0xF7
[PRESET LOAD] 7 6 File name = default 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x06,0x00,0x31,0x46,0xF7
[PRESET SAVE] 7 7 File name = default 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x07,0x00,0x32,0x30,0xF7
[SET MAC ADDR]
7 8
00-05-CD-12-00-70
0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x08,0x0C,0x30,0x30,0x30,0x35,0x43,0x44,0x31
,0x32,0x30,0x30,0x37,0x30,0x41,0x33,0xF7
* 2
[GET MAC ADDR] 7 9 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x09,0x00,0x32,0x32,0xF7
[SYSCFG X Y]
7 10
System config 0:0
0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x0A,0x06,0x30,0x30,0x30,0x30,0x30,0x30,0x34,
0x39,0xF7
* 3
[SYSCFG ALL CHG] 7 11 (All 1) 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x0B,0x22,0x30,0x31,0x30,0x31,0x30,0x31,0x30,
0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x31,0x30,0x30,0x30,0x30,0x30,0x30,
0x30,0x30,0x30,0x30,0x30,0x30,0x30,0x30,0x30,0x30,0x41,0x46,0xF7
* 4
[SYSCFG DEFAULT] 7 12 0xF0,0x00,0x40,0x03,0x11,0x01,0x00,0x07,0x0C,0x00,0x32,0x35,0xF7
* 1 The parameter and checksum (written in red) are variable. The first 2 bytes are Parameter 1 (“00” to “27” in ASCII). Parameter 2 follows (“0000” to “001D” in ASCII). Parameter 1 and 2
are specified in the following table.
* 2 The parameter and checksum (written in red) are variable. Parameter 2 is stored each in 2 bytes.
* 3 The parameter and checksum (written in red) are variable. The Mac address is specified 8 bytes ASCII strings
* 4 The parameter and checksum (written in red) are variable. The first 2 bytes is the SYSCFG index num. (It is “00” to “08” in ASCII). The value (“0000” to “0004” in ASCII) follows it.
* 5 The parameter and checksum (written in red) are variable. The parameter 2 is stored each in 2 bytes.