What to do if my Denon PMA-2000AE Amplifier power indicator doesn't light up?
If the power indicator isn't lighting up and no sound is coming from your Denon Amplifier when you turn it on, the most likely cause is that the power supply cord isn't connected. Make sure it's properly plugged in.
Why is my Denon PMA-2000AE howling when playing records at high volume?
If you are playing records and the volume is turned up and you hear howling from your Denon Amplifier, the issue may be: * The turntable and speaker systems are too close. Move speaker systems as far away as possible. * The floor is soft and vibrates easily. Use cushions to absorb the vibrations transmitted from the floor to the speakers. If the turntable does not include insulators, use audio insulators, available in stores.
How to fix sound only coming from one side on my Denon PMA-2000AE?
If the sound is only coming from one side on your Denon Amplifier, check the following: * Ensure that the speaker cords are securely connected. * Verify that the input cords are also properly connected. * Adjust the BALANCE control knob to correct any imbalance.
What causes distorted sound on my Denon PMA-2000AE Amplifier?
If you're experiencing distorted sound with your Denon Amplifier, it could be due to a few reasons: * The stylus pressure might be too light; try applying the proper pressure. * There could be dirt on the stylus tip; inspect and clean it if necessary. * The cartridge might be defective; consider replacing it.
Why is my Denon PMA-2000AE producing a booming sound when playing records?
If you're playing records and hearing a booming sound with your Denon Amplifier, here's what you can check: * Make sure the turntable's ground wire is securely connected. * Ensure the input cords are properly connected to the PHONO terminals. * Consider if a nearby TV or VCR is causing interference; if so, try repositioning the turntable.
Why is there no sound from my Denon PMA-2000AE Amplifier but the power light is on?
If you're not getting any sound from your Denon Amplifier, even though the power light is on, consider these possibilities: * Ensure the speaker cords are securely connected. * Verify that the INPUT SELECTOR knob or P. DIRECT switch is in the correct position. * Check that the VOLUME control knob isn't turned all the way down; adjust it to a suitable level.
What to do if the Denon PMA-2000AE Amplifier remote control is not working?
If your Denon Amplifier's remote control isn't working, there could be several reasons: * The batteries might be dead. Try replacing them with new ones. * You might be too far away. Move closer to the unit. * There could be something blocking the signal. Make sure there's nothing between the remote and the amplifier. * Ensure you're pressing the correct button. * Also, check that the batteries are inserted correctly, with the positive and negative ends in the right direction.
Essential safety instructions and precautions for operating and servicing the unit.
Procedures for leakage current and post-service safety inspections.
Guidelines on electric shock, disassembly, part usage, and reassembly.
Guidance on using designated parts for critical safety components.
Steps for setting up and performing the idling current adjustment.
Diagram illustrating signal flow, functional blocks, and voltage levels.
Pinout and internal block diagram of the TMP87CC46N microcontroller.
Detailed description of each pin's function, I/O type, and port name for IC901.
Information on various other ICs, transistors, diodes, thyristors, and thermistors.
Details on diodes, thyristors, and thermistors used in the unit.
Layout diagram for the Input/Control Printed Wiring Board.
Layout diagrams for the Power Amplifier Printed Wiring Boards and related units.
Layout diagram for the Flat Amplifier Printed Wiring Board.
Explanations for special marks and notations used in the parts list.
Guide to interpreting resistor and capacitor codes and values.
List of semiconductors (ICs, transistors, diodes) for the Input/Control P.W.B.
List of resistors and capacitors for the Input/Control P.W.B.
List of miscellaneous parts (connectors, jacks, relays) for the Input/Control P.W.B.
List of semiconductors and resistors for the Power Amp P.W.B.
List of capacitors and miscellaneous parts for the Power Amp P.W.B.
List of connectors, fuses, jacks, relays, and switches for the Power Amp P.W.B.
List of semiconductors and resistors for the Flat Amp P.W.B.
List of capacitors and miscellaneous parts for the Flat Amp P.W.B.
Visual representation of the unit's assembly with numbered components.
Detailed list of parts for each major assembly unit.
List of chassis components, screws, washers, and other miscellaneous parts.
List of various cords, wires, and connector types.
List of packaging materials and accessories included with the unit.
Diagram illustrating wiring connections between internal units.
Safety warnings and explanations of notation used in schematic diagrams.
Schematic diagram for the Input/Control and Protection units.
Schematic diagram for the Power Amplifier (Lch/Rch) and related units.
Schematic diagram for the Flat Amplifier unit.
List of parts marked for WEEE recycling by assembly unit.
Details on materials for WEEE-marked parts and screws.
Detailed visual representation of the unit's assembly with numbered components.
Diagrams and material lists for power transformer recycle parts.
To Next Page
General
