Denon RCD-M39 User Manual (English)

Other manuals for Denon RCD-M39

Service Manual105 pages

Getting Started9 pages

Getting Started Guide9 pages

Questions and Answers:

M
michelle97Sep 4, 2025
Why isn't 'USB' displayed on my Denon Receiver when I connect a USB memory device?
- W
  Walter GibsonSep 4, 2025
  If 'USB' is not displayed on your Denon Receiver when a USB memory device is connected, first check the connection. It could be that the set cannot recognize the USB memory device. Also, ensure that the USB memory device conforms to mass storage class or MTP standards. Note that DENON does not guarantee that all USB memory devices will operate or receive power. If you are connecting via a USB hub, connect the USB memory device directly to the USB port.
S
Sheila HerringAug 25, 2025
What to do if my Denon Receiver isn't responding to the remote control?
- J
  John KingAug 25, 2025
  If your Denon Receiver isn't responding to the remote control, consider these possible causes: * The batteries may be worn, so replace them with new ones. * You may be operating the remote outside of its specified range; try moving closer. * There might be an obstacle between the remote and the main unit; remove any obstructions. * The batteries might be inserted incorrectly; check the polarity marks in the battery compartment and correct the battery direction. * The remote control sensor on the set may be exposed to strong light; move the set to a location where the sensor is not exposed to direct sunlight or fluorescent light.
S
Steven DanielsAug 25, 2025
Why does my Denon Receiver turn off suddenly and the power indicator flashes red?
- T
  Tanya WernerAug 26, 2025
  Your Denon Receiver might be turning off suddenly with a flashing red power indicator (flashing at 0.5 second intervals) because the protection circuit has been activated due to a rise in internal temperature. Turn off the power, wait for the unit to fully cool down, and then turn it back on. Another cause could be that the core wires of two speakers are touching, or a core wire is sticking out and touching the set's rear panel, which also activates the protection circuit. Unplug the power cord first, then twist the core wires tightly or terminate the speaker cables, and then reconnect.
M
Misty MayerAug 27, 2025
What does it mean when my Denon Receiver's power turns off and the power indicator flashes red?
- M
  moodyrichardAug 27, 2025
  If your Denon Receiver's power turns off suddenly and the power indicator flashes red (flashing at 0.25 second intervals), it indicates that the set is damaged. Turn off the power and contact a DENON service center.
M
Michelle GillAug 27, 2025
How to fix Denon Receiver when files on a USB memory device cannot be played?
- J
  Jacqueline RichardsAug 27, 2025
  If files on a USB memory device cannot be played on your Denon Receiver, the USB memory device might be in a format other than FAT16 or FAT32; set the format to FAT16 or FAT32. If the USB memory device is divided into multiple partitions, only files stored in the top partition can be played. The files may also be stored in a non-compatible format; record the files in a compatible format. Finally, files that are copyright protected cannot be played on this set.
V
Vanessa RodriguezAug 28, 2025
How do I turn on the display on my Denon Receiver?
- B
  Barbara FordAug 28, 2025
  If the display on your Denon Receiver is off, the Dimmer setting is likely set to “OFF”. Change the Dimmer setting to something other than “OFF”.
C
Cynthia CombsSep 9, 2025
Why does my Denon Receiver show '00 Tr 00 : 00' when a CD is loaded?
- W
  Wanda PhillipsSep 10, 2025
  If your Denon Receiver shows '00 Tr 00 : 00' on the display even though a CD is loaded, the disc is not properly loaded. Reload the disc.
J
Jessica DavisSep 5, 2025
Why can't I play my iPod on my Denon Receiver?
- K
  Kelli FrankSep 5, 2025
  If you cannot play your iPod on your Denon Receiver, make sure that the input source is set to “USB”. Also, check that the cable is properly connected; try reconnecting it.
A
Alejandra MartinSep 3, 2025
What to do if the display is not lit and sound is not produced when power switched to on for my Denon RCD-M39?
- J
  Jesse RoseSep 3, 2025
  If the display is not lit and no sound is produced when the power is switched on, check the connections on the set's rear panel and the connection of the power plug to the power outlet to ensure the power cord is securely plugged in.
C
Christopher HillSep 1, 2025
What to do if my Denon RCD-M39 Car Receiver display shows “00 Tr 00 : 00” even though a CD is loaded?
- D
  Dr. Dawn Briggs DDSSep 1, 2025
  If “00 Tr 00 : 00” is shown on the display even though a CD is loaded, the disc is not properly loaded. Reload the disc.