DeWalt DCS778

36
ENGLISH
MAINTENANCE
Your
DeWALT
power tool has been designed to operate over a long period
of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regularcleaning.

WARNING: To reduce the risk of serious personal injury, turn
machine off and disconnect battery pack before making any
adjustments or removing/installing attachments or accessories.
An accidental start-up can causeinjury.

WARNING: If the saw blade is worn replace it with a new sharpblade.
Lubrication
Your power tool requires no additionallubrication.
Cleaning
Before use, carefully check the upper blade guard, movable lower blade
guard as well as the dust extraction tube to determine that it will operate
properly. Ensure that chips, dust or workpiece particle cannot lead to
blockage of one of thefunctions.
In case of workpiece fragments jammed between saw blade and guards
disconnect the machine from the power supply and follow the instructions
given in section Mounting the saw blade. Remove the jammed parts and
reassembling the sawblade.

WARNING: Blow dirt and dust out of the main housing with dry air
as often as dirt is seen collecting in and around the air vents. Wear
approved eye protection and approved dust mask when performing
thisprocedure.

WARNING: Never use solvents or other harsh chemicals for cleaning
the non-metallic parts of the tool. These chemicals may weaken the
materials used in these parts. Use a cloth dampened only with water
and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into aliquid.

WARNING: To reduce the risk of injury, regularly clean the
tabletop.

WARNING: To reduce the risk of injury, regularly clean the dust
collectionsystem.
Optional Accessories

WARNING: Since accessories, other than those offered by
DeWALT
,
have not been tested with this product, use of such accessories with
this tool could be hazardous. To reduce the risk of injury, only
DeWALT
,
recommended accessories should be used with thisproduct.
Support For Long Pieces (Fig. V)
• Always support long pieces.
• For best results, use the extension work support (DE7023) to extend
the table width of your saw (available from your dealer as an option).
Support long workpieces using any convenient means such as saw-
horses or similar devices to keep the ends from dropping.
Range of saw blades available (recommended
blades)
Type of blade Blade dimensions
(diameter x bore x no. of teeth)
Usage
DT1158 series 30 250x30x24 For general purpose, ripping and cross-
cutting of wood and plastics
DT4282 series 40 250x30x96 TCG for use with aluminum
DT4226 series 40 250x30x30 ATB for fine cutting of ` manmade and
natural wood
DT4287 series 40 250x30x80 TCG for extra fine cutting of manmade and
natural wood
DT99571-QZ 250x30x24 24T Flexvolt blade for general purpose,
ripping and cross cutting
DT99572-QZ 250x30x36 36T Flexvolt blade for fine cutting
DT99573-QZ 250x30x60 60T Flexvolt blade for ultra-fine cutting
Consult your dealer for further information on the appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked with this
symbol must not be disposed of with normal householdwaste.
Products and batteries contain materials that can be recovered or
recycled reducing the demand for raw materials. Please recycle
electrical products and batteries according to local provisions. Further
information is available at www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails to produce
sufficient power on jobs which were easily done before. At the end of its
technical life, discard it with due care for our environment:
• Run the battery pack down completely, then remove it from thetool.
• Li-Ion cells are recyclable. Take them to your dealer or a local recycling
station. The collected battery packs will be recycled or disposed
ofproperly.