Why does my Dexter Laundry T-350 Washer start but not operate?
If your Dexter Laundry Washer starts but doesn't operate, check for error codes and refer to the individual error code descriptions.
Why does water drain slowly from my Dexter Laundry T-350 Washer?
If your Dexter Laundry Washer is draining slowly, check the hoses and drain valve for any blockages. Ensure the drain size is adequate. If necessary, inspect the building drains for blockages.
What causes the water level to be too high in my Dexter Laundry Washer?
If the water level is too high in your Dexter Laundry Washer, check the pressure switch hose for blockage. Also, check for the pressure switch opening circuit across terminals and replace the switch if contacts do not open.
What causes a Dexter Laundry T-350 to not stop?
If your Dexter Laundry Washer doesn't stop, the main PCB, which controls the time cycle at the end of the cycle, may be the issue. You should also check the braking resistors for continuity and verify their ohms resistance.
Why doesn't water flush the softener compartment in my Dexter Laundry T-350?
If water isn't flushing the softener compartment in your Dexter Laundry Washer, check the water valve coil for continuity at the terminals and replace it if there's no continuity. Inspect the water inlet screens for blockage and clean them if necessary. Ensure that the water supply is turned on and operating. Also, check the pressure switch continuity between terminals; if there's no continuity, check the pressure switch hose for obstruction, and if the hose is okay, change the pressure switch.
Why is there no hot water in the detergent dispenser of my Dexter Laundry T-350?
If there's no hot water in the detergent dispenser of your Dexter Laundry Washer, check the water valve coil continuity at the terminals and replace it if there is no continuity. Remember, there is 120 VAC power (60Hz) only on for 20 seconds in the wash bath (24 VAC for 50 Hz models). Inspect the water inlet screens for blockage and clean them if necessary. Ensure that the water supply is turned on and operating. Also, check the wire harness to the valve.
Why is there no cold water entering the tub in my Dexter Laundry Washer during wash?
If no cold water is entering the tub of your Dexter Laundry Washer during the wash cycle, start by checking the water valve coil for continuity at the terminals and replace it if necessary. Inspect the water inlet screens for any blockage and clean them if needed. Ensure that the water supply is turned on and functioning correctly. If the appropriate voltage is not present at the valve, refer to the wiring diagram for your specific washer model. Check for voltage at the P4 Connector on the Relay PCB and for LED indication that the appropriate relay is activated. Check the pressure switch continuity between terminal contacts; if there's no continuity, check the pressure switch hose for obstructions, and if the hose is clear, replace the pressure switch.
How to open a Dexter Laundry Washer door that will not open?
If the door of your Dexter Laundry Washer won't open, check if the thermoactuator and its mechanism are stuck or binding. Ensure the locking thermoactuator is not receiving 24VAC during the last 1 1/2 minutes of the cycle and that the unlocking thermoactuator is receiving 24VAC during the last minute. If the timing and voltage are correct, replace the thermoactuator. Also, verify that the door rod from the mechanism to the lock assembly is long enough to allow the lock assembly to disengage; adjust the rod or the position of the mechanism if needed. Check that the door lock mechanism is not stuck closed; if it is, replace it.
What to do if the door of my Dexter Laundry T-350 does not lock?
If the door of your Dexter Laundry Washer isn't locking, first check the display for any error messages and follow the tests described in the fault code section. Then, verify that the door locking mechanism is receiving 120VAC (for 60 Hz models) or 24VAC (for 50 Hz models) from the main relay PCB; if it's receiving power but not functioning, replace the mechanism. Also, check the door switch for continuity through the door latch.
How to stop water leakage around the loading door of my Dexter Laundry T-350?
If you're experiencing water leakage around the loading door of your Dexter Laundry Washer, the door may need adjustment due to wear. Check the tightness around the door's perimeter. Adjust the left to right tightness by using shims at the door lock or hinge side. Ensure the gasket is centered to the tub opening before tightening the door to hinge bolts. If the gasket is deformed, worn, or damaged, consider replacing it.
General| Brand | Dexter Laundry |
|---|---|
| Model | T-350 |
| Category | Washer |
| Language | English |
To Next Page
