Dexter Laundry WN0900

Questions and Answers

S
Sara RodriguezSep 7, 2025
What to do if cold water does not enter the tub in wash cycle of my Dexter Laundry WN0900 Washer?
- M
  Michael AustinSep 7, 2025
  If cold water isn't entering the tub during the wash cycle of your Dexter Laundry Washer, start by checking the water valve coil for continuity at the terminals and replace it if there's no continuity. Also, check for 24 VAC (50 Hz) power from the main relay PCB. Inspect the water inlet screens for blockage and clean them if necessary. Ensure that the water supply is turned on and operating correctly. Finally, check the black and white wire at the Molex plug on the main PCB controller P21 connection and at the PCB relay board P20 connection, and examine the pressure switch continuity between terminal contacts. If no continuity, check the pressure switch hose for obstruction. If the hose is okay then change the pressure switch.
K
Kyle ShawAug 27, 2025
What causes excessive vibration in Dexter Laundry Washer?
- S
  Sandy LucasAug 27, 2025
  If your Dexter Laundry Washer experiences excessive vibration, check the strength of the mounting structure, concrete, or base, and ensure the mounting bolts are tightened. A worn drive belt or damaged pulleys can also cause vibration and noise, so inspect these components. Be sure you wash recommended load size as specified for washer model (in lb/kg). Small loads contribute to out of balance loading and increase vibration.
C
caseycrystalDec 1, 2025
Why my Dexter Laundry Washer does not start?
- K
  Keith MoodyDec 1, 2025
  If your Dexter Laundry Washer does not start, several factors could be at play. Start by examining the power supply, checking circuit breakers, voltage, power leads, and connections, and see if the front display LED shows a dollar amount. Then, check the door switch for continuity when closed; adjust or replace it if there's none. Also, inspect the control breaker or fuse (1.5 amp, or 2.5 amp for T-1200) for continuity, replacing it if needed. Verify the control transformer's voltage output (120VAC), replacing the transformer if incorrect. Make sure that all wire connections of PCB board and Relay PCB are firmly in contact. Check the wiring between PCB, unplug the data cable phone type connectors and VFD and replug with power removed. Finally, confirm 120V power reaches the door solenoid w...
L
Logan WalkerSep 13, 2025
Why Dexter Laundry WN0900 machine does not turn?
- M
  Mrs. Jennifer AndersonSep 14, 2025
  To troubleshoot why your Dexter Laundry Washer isn't turning, begin by checking the VFD (Variable Frequency Drive). Remove the inspection panel and note any numbers or letters displayed. If there's no display, turn off the power to the machine at the breaker for two minutes, then turn it back on to reset. If the issue persists and there's still no display, consider replacing the VFD.
K
kbrownSep 23, 2025
What to do if the door will not open on Dexter Laundry Washer/Dryer?
- K
  katherine33Sep 23, 2025
  If the door on your Dexter Laundry Washer/Dryer won't open, check if the thermoactuator(s) and its mechanism are stuck or binding, preventing the door lock solenoid from opening. Ensure the locking thermoactuator isn't receiving 120VAC during the last 1 1/2 minutes of the cycle and that the unlocking thermoactuator is receiving 120VAC during the last minute. If the thermoactuators don't receive voltage at the correct times, change the timer. If the timing and voltage are correct, replace the thermoactuator.
A
Aaron MarshallSep 12, 2025
What to do if hot water does not enter tub in wash for Dexter Laundry WN0900?
- M
  Mark BrownSep 12, 2025
  If hot water isn't entering the tub during the wash cycle of your Dexter Laundry Washer, start by checking the water valve coil for continuity at its terminals and ensure it's receiving the correct voltage from the main relay PCB. Replace the coil if there's no continuity. Inspect the water inlet screens for any blockages and clean them if necessary. Confirm that the water supply is turned on and functioning correctly. Check the black and white wires at the Molex plug on the PCB at the main controller and at the relay PCB. Also, check the pressure switch continuity between terminals; if there's no continuity, inspect the pressure switch hose for obstructions and replace the switch if the hose is clear.
J
josebarnesSep 4, 2025
What to do if my Dexter Laundry Washer does not stop?
- L
  Lauren LaneSep 4, 2025
  If your Dexter Laundry Washer does not stop, remember that the main PCB controls the time cycle at the end of the cycle. Also, check the braking resistors for continuity and verify the ohms resistance by Molex.
W
wrightrobertNov 23, 2025
What to do if Dexter Laundry Washer starts but will not advance in the cycle?
- R
  Rebecca YoderNov 23, 2025
  If your Dexter Laundry Washer starts but doesn't advance in its cycle, begin by checking the water valves to ensure they're operating. Look for the illuminated red light on the Input/Output PCB for the water valves (#5, #6, #7, #8) and confirm the board is sending 120VAC to the valve. Replace the valve if it receives 120VAC but doesn't function; otherwise, check the Input/Output PCB. Next, verify the drain valve is closing properly and check for 120VAC to the drain valve from Input/Output PCB red light #4. Replace or clean the drain valve if it receives 120VAC but doesn't close; if there's no voltage, inspect the CPU board, ribbon cable, and I/O PCB. Clear any obstructions from the fill hose or water valve screens. Ensure the water supply is turned on and working. Examine the pressure swit...
P
parksjasonSep 17, 2025
Why Dexter Laundry WN0900 Washer water drains slowly?
- T
  Taylor WilliamsSep 17, 2025
  If water is draining slowly from your Dexter Laundry Washer, inspect the hoses and drain valve for any blockages. Ensure the drain size is adequate. If necessary, check the building drains for blockages.
D
Danielle HarrisSep 1, 2025
Why no cold water to tub in wash for Dexter Laundry WN0900 Washer?
- D
  Dakota PattonSep 1, 2025
  If cold water isn't entering the tub during the wash cycle of your Dexter Laundry Washer, start by checking the water valve coil for continuity at its terminals; replace it if there's no continuity. Next, inspect the water inlet screens for blockages and clean them if necessary. Ensure that the water supply is turned on and operating correctly. Check the black or white wires at the Molex plug on the PCB at the main controller and at the relay PCB. Lastly, test the pressure switch for continuity between terminal contacts; if there's no continuity, check the pressure switch hose for obstructions, and replace the switch if the hose is clear.