Dexter Laundry WCAD Series

Other manuals for Dexter Laundry WCAD Series

Programming Instructions6 pages

Parts And Service Manual96 pages

Questions and Answers

L
Lisa BarrettSep 23, 2025
What to do if the door will not open on my Dexter Laundry WCAD Washer/Dryer?
- E
  Elizabeth RojasSep 23, 2025
  If the door on your Dexter Laundry Washer/Dryer won't open, check the thermoactuator(s) and its mechanism to see if it's stuck or binding, preventing the door lock solenoid from opening. Ensure the locking thermoactuator isn't receiving 120VAC during the last 1 1/2 minutes of the cycle, and that the unlocking thermoactuator is receiving 120VAC during the last minute of the cycle. If the thermoactuators don't receive voltage at the correct times, change the timer. If the timing and voltage are correct, replace the thermoactuator.
A
Amanda VasquezAug 25, 2025
What to do if Dexter Laundry Washer machine will not accept coins?
- W
  Wayne GarciaAug 26, 2025
  If your Dexter Laundry Washer isn't accepting or counting coins, check these areas: * **Coin Acceptor:** Look for blockages or damage in the coin acceptor switch. Clean, adjust, or replace it as needed. * **Power Supply:** Check circuit breakers, voltage, power leads, and power connections. * **Door Closed Safety Switch:** Verify the door closed switch at the door hinge is working correctly. * **Door Handle Closed Switch:** Ensure the single door closed switch on the left side of the door handle closes when the handle is vertical. * **Control Breaker or Fuse:** Check the breaker or fuse for continuity and replace if necessary. (Use a 1.5 amp fuse for T-300 through T-950 models, and a 2.5 amp fuse for T-1200 and T-1450 models.) * **Main PCB:** Consider replacing the main PCB.
T
Theresa SmithAug 26, 2025
How to reduce excessive vibration in Dexter Laundry WCAD?
- J
  John StricklandAug 27, 2025
  If your Dexter Laundry Washer is vibrating excessively, consider the following: * **Mounting System:** Check the strength of the mounting structure (concrete or base) and ensure mounting bolts are tight. * **Drive Belt:** A worn drive belt can cause vibration and noise, so inspect it. * **Loading:** Small loads can contribute to imbalance and increase vibration.
C
Carrie HillAug 27, 2025
Why Dexter Laundry WCAD door does not lock?
- A
  Alex ChapmanAug 27, 2025
  If the door on your Dexter Laundry Washer isn't locking, try these steps: * **Check Display:** See if a Door Lock Error is displayed. If so, follow the tests in the fault code section. * **Door Locking Motor:** Make sure the motor is receiving 120VAC from the main relay PCB. If it is, replace the solenoid. * **Door Switch:** Check for continuity through the door latch switch when the door is closed. Adjust or replace the door switch if there's no continuity.
W
Wanda WeberNov 22, 2025
Why Dexter Laundry WCAD Washer machine does not start?
- J
  James MunozNov 22, 2025
  If your Dexter Laundry Washer doesn't start, here's what to check: * **Power Supply:** Ensure circuit breakers are on, check the voltage, power leads, and connections. See if the front display LED shows a dollar amount. * **Door Switch:** Verify continuity through the door switch when the door is closed. Adjust or replace the switch if there's no continuity. * **Control Breaker or Fuse:** Check the 1.5 amp breaker or fuse (2.5 amp for T-950 and T-1200 models) for continuity; replace if needed. * **Control Transformer:** Check the voltage output from the control transformer for 120VAC; replace the transformer if the voltage is incorrect. * **Coin Acceptor:** Inspect the coin acceptor for blockages or damage; clean or replace it. * **PCB Board:** Check all wire connections for s...
C
Candace SawyerSep 12, 2025
Why does the door on my Dexter Laundry WCAD not lock?
- B
  Brandon JamesSep 13, 2025
  If the door on your Dexter Laundry Washer isn't locking, check the display for a fault code. If F1 is displayed, follow the tests described in the fault code section. Also, check if the door locking solenoid is receiving 120VAC from the main relay PCB; if it is, replace the solenoid. Finally, check the door latch switch for continuity when the door is closed; adjust or replace the door switch if there's no continuity.
J
John CampbellSep 12, 2025
Why Dexter Laundry Washer starts goes directly to end of cycle?
- M
  Mark LopezSep 12, 2025
  If your Dexter Laundry Washer starts and immediately goes to the end of the cycle, displaying 'PUSH' then '0' or '00', the E-Stop button or switch may be faulty. Replace the switch assembly.
J
Jeffrey MarksSep 12, 2025
What to do if my Dexter Laundry WCAD Washer does not start?
- D
  dbutlerSep 12, 2025
  If your Dexter Laundry Washer isn't starting, begin by checking the power supply: inspect the circuit breakers, voltage, power leads, and power connections. See if the front display LED is showing a dollar amount. Then check the door switch for continuity when the door is closed; adjust or replace it if there's no continuity. Also, check the 1.5 amp breaker or fuse for continuity (T-1200 uses 2.5amp); replace it if necessary. Verify the voltage output from the control transformer is 120VAC; replace the transformer if the voltage is incorrect. Additionally, inspect the PCB board, the wiring between PCB, the Relay PCB and the Door Solenoid.
K
kelly46Sep 4, 2025
Why Dexter Laundry WCAD tumbles in one direction?
- J
  John RamosSep 4, 2025
  If your Dexter Laundry Washer only tumbles in one direction, you can check the following: * **VFD:** Remove the top cover and note if the power light or fault lights are displayed. Check the front control for related codes and refer to the fault code section for more information. * **Wiring:** Inspect the yellow enable wires from the main relay PCB and at the VFD.
T
Theresa CookeSep 2, 2025
What to do if Dexter Laundry WCAD machine does not turn?
- R
  robert50Sep 2, 2025
  If your Dexter Laundry Washer isn't turning, check the VFD by removing the top panel and noting if any power or fault lights are illuminated. If the fault light is on, turn off the power to the machine at the breaker for 2 minutes, then turn it back on to reset. If there's still no display, replace the VFD.

Summary

Equipment Safety Warnings and Symbols

Safety Symbol Definitions

Explains the meaning of hazard symbols like DANGER, WARNING, CAUTION, and NOTICE.

Specific Safety Advisories

Provides specific cautions regarding electrical hazards, sharp edges, and water inlet temperatures.

Prohibited and Mandatory Actions

Lists prohibited operations and mandatory safety actions for washer use.

Section 1: Machine Mounting & Installation

Model Specifications

Outlines technical specifications for various WCAD washer models.

Mounting Dimensions and Pad Details

Provides detailed diagrams and requirements for mounting and pedestal installation.

Section 2: Machine Installation & Operating Instructions

Installation Requirements

Covers essential requirements for installing the washer, including foundation, plumbing, and electrical.

Washer Operation

Details how to operate the washer, including loading, detergent use, and cycle completion.

Section 3: Machine Programming Instructions

Programming Overview and Coin Price Setup

Guides on programming wash cycles, coin prices, and temperature pricing.

Wash Cycle and Rapid Advance Programming

Details programming wash cycle parameters and using the Rapid Advance mode.

Section 4: Trouble Shooting

Common Troubleshooting Solutions

Lists common symptoms, probable causes, and suggested remedies for washer malfunctions.

Machine Fault Error Codes

Details specific fault codes displayed on the washer and required actions.

Section 5: Machine Service Procedures

Panel and Cover Removal

Step-by-step instructions for removing various external panels and covers for access.

Door and Lock Mechanism Service

Procedures for servicing the door, hinges, lock mechanism, and nameplate.

Cabinet, Drive Belt, and Motor Service

Steps for removing the outer cabinet, door lock components, drive belt, and motor.

Tub, Bearing, and Cylinder Assembly Service

Detailed steps for removing and reassembling the tub back, bearing, and cylinder assembly.

Bolt Torque Specifications

Provides essential torque specifications for reassembly of various components.

Section 6: Service Electrical Components

Control Trough Components

Details components housed within the control trough, including PCBs, transformers, and cables.

Section 7: Electrical Wiring Diagrams & Schematics

Circuit Operation Descriptions

Explains the operational logic of various machine circuits, including start, fill, wash, drain, and spin.

Wiring Diagrams and Schematics

Presents detailed wiring diagrams and schematics for different washer configurations.

Section 8: Parts Data

Parts Lists by Model

Comprehensive lists of part numbers for various washer components and assemblies.

Wiring Harness Part Numbers

Provides part numbers for wiring harnesses specific to different washer models.

Section 10: EasyCard Interface

EasyCard Control Panel Parts

Lists part numbers for integrated EasyCard control panel components.

Reader Harness and Address Switch

Diagrams showing the reader wire harness connection and address switch location.

Section 11: Parts 50 Hz Models

50 Hz Model Specific Parts Lists

Notes that parts in this section are specific to 50Hz models.

Transformer, Filter, and Coin Handling Parts

Part numbers for transformers, filters, and coin handling components for specific models.

Water Valve, Drain Valve, and Door Locking Parts

Part numbers for water valves, drain valves, and door locking components for specific models.

Section 12: Maintenance

Preventative Maintenance Schedule

Provides daily and quarterly maintenance tasks for optimal washer performance.

Section 9: Coin Handling

Coin Handling Parts and Schematics

Lists part numbers and provides wiring diagrams for coin handling systems.

Mechanical and Electronic Acceptor Service

Guides on adjusting, maintaining, and converting coin acceptors for optimal operation.