Why Dexter Laundry Washer starts goes directly to end of cycle?
If your Dexter Laundry Washer starts and immediately goes to the end of the cycle, displaying 'PUSH' then '0' or '00', the E-Stop button or switch may be faulty. Replace the switch assembly.
What to do if door will not open in Dexter Laundry WCAD Washer?
If the door of your Dexter Laundry Washer will not open, check to see if the thermoactuator(s) and/or its mechanism is stuck or binding and not allowing the door lock solenoid to open. Check to be sure that the locking thermoactuator is not receiving 120VAC during the last 1 1/2 minutes of the cycle and that the unlocking thermoactuator is receiving 120VAC during the last minute of the cycle. If the thermoactuators do not receive voltage at the correct times, change the timer. If the timing and voltage are correct, replace the thermoactuator.
Why water does not fill softener compartment in Dexter Laundry WCAD?
If water isn't filling the softener compartment in your Dexter Laundry Washer, check these: * **Water Valve Coil:** Check the coil continuity at the terminals and replace if there's no continuity. * **Water Inlet Screens:** Check the water inlet screens for blockage and clean if necessary. * **Water:** Ensure that the water is turned on and operating.
Why Dexter Laundry WCAD Washer machine does not stop?
If your Dexter Laundry Washer doesn't stop, it could be due to: * **Main PCB:** The main PCB controls the time cycle at the end of the cycle. * **Braking Resistors:** Check the braking resistors for continuity and verify the ohms resistance by Molex.
How to open Dexter Laundry WCAD door?
If the door of your Dexter Laundry Washer won't open, check the following: * **Door Rod:** Ensure the door rod from the solenoid to the lock assembly is long enough to allow the lock assembly to disengage. Adjust the rod if necessary. * **Gear Motor:** Check the door lock motor to ensure it's not stuck or binding. Replace the locking motor if it doesn't move freely.
What to do if Dexter Laundry WCAD starts and does not operate?
If your Dexter Laundry Washer starts but doesn't operate, check that the yellow enable wires from relay PCB P13 & motor P14 to the VFD are connected and advancing through the cycle. Check the fault code on the VFD before removing power from the drive. Also, check the orange P-15 wire for a signal from the door switches.
Why Dexter Laundry WCAD tumbles in one direction?
If your Dexter Laundry Washer only tumbles in one direction, you can check the following: * **VFD:** Remove the top cover and note if the power light or fault lights are displayed. Check the front control for related codes and refer to the fault code section for more information. * **Wiring:** Inspect the yellow enable wires from the main relay PCB and at the VFD.
Why Dexter Laundry WCAD Washer water drains slowly?
If water is draining slowly from your Dexter Laundry Washer, inspect the hoses and drain valve for blockages. Clean them if necessary and ensure they are adequately sized. Also, check the building drains for any blockages.
What to do if Dexter Laundry WCAD machine does not turn?
If your Dexter Laundry Washer isn't turning, check the VFD by removing the top panel and noting if any power or fault lights are illuminated. If the fault light is on, turn off the power to the machine at the breaker for 2 minutes, then turn it back on to reset. If there's still no display, replace the VFD.
Why no hot water in detergent dispenser of Dexter Laundry WCAD Washer?
If there's no hot water in the detergent dispenser of your Dexter Laundry Washer, check the following: * **Water Valve Coil:** Check the coil continuity at the terminals and replace if there's no continuity. Note that 120V power is only on for 20 seconds in the wash bath. * **Water Inlet:** Check the water inlet screens for blockage and clean the screens if necessary. * **Water:** Ensure that the water is turned on and operating. * **Wiring:** Check the black & white harness.
General| Brand | Dexter Laundry |
|---|---|
| Model | WCAD Series |
| Category | Washer |
| Language | English |
Explains the meaning of hazard symbols like DANGER, WARNING, CAUTION, and NOTICE.
Provides specific cautions regarding electrical hazards, sharp edges, and water inlet temperatures.
Lists prohibited operations and mandatory safety actions for washer use.
Outlines technical specifications for various WCAD washer models.
Provides detailed diagrams and requirements for mounting and pedestal installation.
Covers essential requirements for installing the washer, including foundation, plumbing, and electrical.
Details how to operate the washer, including loading, detergent use, and cycle completion.
Guides on programming wash cycles, coin prices, and temperature pricing.
Details programming wash cycle parameters and using the Rapid Advance mode.
Lists common symptoms, probable causes, and suggested remedies for washer malfunctions.
Details specific fault codes displayed on the washer and required actions.
Step-by-step instructions for removing various external panels and covers for access.
Procedures for servicing the door, hinges, lock mechanism, and nameplate.
Steps for removing the outer cabinet, door lock components, drive belt, and motor.
Detailed steps for removing and reassembling the tub back, bearing, and cylinder assembly.
Provides essential torque specifications for reassembly of various components.
Details components housed within the control trough, including PCBs, transformers, and cables.
Explains the operational logic of various machine circuits, including start, fill, wash, drain, and spin.
Presents detailed wiring diagrams and schematics for different washer configurations.
Comprehensive lists of part numbers for various washer components and assemblies.
Provides part numbers for wiring harnesses specific to different washer models.
Lists part numbers for integrated EasyCard control panel components.
Diagrams showing the reader wire harness connection and address switch location.
Notes that parts in this section are specific to 50Hz models.
Part numbers for transformers, filters, and coin handling components for specific models.
Part numbers for water valves, drain valves, and door locking components for specific models.
Provides daily and quarterly maintenance tasks for optimal washer performance.
Lists part numbers and provides wiring diagrams for coin handling systems.
Guides on adjusting, maintaining, and converting coin acceptors for optimal operation.
To Next Page
