What does 'NO PROX SENSOR OUTPUT' mean on my Dexter Laundry Dryer?
If your Dexter Laundry Dryer displays 'NO PROX SENSOR OUTPUT', it means the machine control isn't detecting output from the proximity sensor(s) when the cylinder is supposed to turn. Inspect the gap on the sensor and update the firmware to the latest version.
What to do if my Dexter Laundry T-80 Dryer shows 'HEAT RISE OUT OF RANGE'?
If your Dexter Laundry Dryer displays 'HEAT RISE OUT OF RANGE', inspect the temperature probe and its connections. Perform an Ohm test on the temperature probe, which should measure 10K Ohms at room temperature.
Why is my Dexter Laundry T-80 taking so long to dry?
Several factors can cause slow drying. Make sure the correct temperature setting is selected. Clean the lint screen. Ensure there are no air flow restrictions and that make-up air adheres to installation guidelines. Also, check the exhaust for any obstructions, following the installation guidelines.
What does 'TEMP SENSOR OPEN' mean on my Dexter Laundry Dryer and how do I fix it?
If your Dexter Laundry Dryer shows 'TEMP SENSOR OPEN', inspect the temperature probe wires. Perform an Ohm test on the temperature probe; it should measure 10K Ohms at room temperature.
What to do if my Dexter Laundry Dryer displays 'TEMP SENSOR SHORT'?
If your Dexter Laundry Dryer displays 'TEMP SENSOR SHORT', inspect the temperature probe wires. Ohm test the temperature probe; it should read 10K Ohms at room temperature.
What does 'Close Door' mean on my Dexter Laundry T-80 Dryer?
The 'Close Door' message on your Dexter Laundry Dryer indicates that either the loading door or the lint compartment door circuit is not closed. Inspect the door switches and wiring. Also, check the lint door paddle to ensure it fully engages the lint door switch.
How to troubleshoot a 'Drive Overcurrent' error on my Dexter Laundry T-80 Dryer?
To troubleshoot a 'Drive Overcurrent' error on your Dexter Laundry Dryer: 1. Check that the dryer cylinder turns freely by hand. If it doesn't, remove the belt and see if the motor turns freely. If the motor doesn't turn freely, replace it. Check for obstructions in the cylinder or check the bearings. 2. Check the motor wires for a short circuit. Separate and insulate any touching conductors; splice broken wires or replace the motor. 3. Check braking resistors to ensure they measure the correct resistance. Replace any resistors that don't measure properly.
What to do if my Dexter Laundry Dryer shows a 'Brown Out' error?
If your Dexter Laundry Dryer displays a 'Brown Out' error, test the incoming power to ensure the transformer is on the correct tap. Inspect the control board, and visually check resistor R185. If the resistor appears burnt, replace the control board after correcting the voltage issue to the machine.
What to do if my Dexter Laundry T-80 Dryer experiences a power loss?
If your Dexter Laundry Dryer experiences a power loss, test the incoming voltage and ensure it matches the correct transformer tap. Also, test the step-down transformer to confirm the voltage is within the appropriate range.
Why does my Dexter Laundry T-80 Dryer say 'Operation in Progress'?
The 'Operation in Progress' message on your Dexter Laundry Dryer indicates that the current drying cycle hasn't finished. The error will automatically disappear once the operation is complete.
Critical warnings about injury, death, property damage, and adherence to instructions.
Restrictions on drying water-cleaned fabrics and risks with flammable substances.
Guidelines for electrical safety, grounding, and qualified personnel for servicing.
Instructions for safe dryer operation, disconnection, and installation.
Step-by-step guide for installing the dryer, including uncrating, clearances, and connections.
Guidance for diagnosing and resolving common dryer issues and understanding fault codes.
General| Brand | Dexter Laundry |
|---|---|
| Model | T-80 |
| Category | Dryer |
| Language | English |
To Next Page
