To Next PageTo Next PageHow to fix no ammeter reading on DieHard Battery Charger?
A lack of reading on the ammeter can be due to poor clamp connections or using the 2-amp charge rate. Inspect the connections to the battery and frame, ensuring they are clean. Rock the clips back and forth to improve the connection. Note that the ammeter may not show activity at the 2-amp charge rate.
What to do if my DieHard Battery Charger circuit breaker cycles on and off?
The circuit breaker cycles when the current draw is too high. Here's what you can do: 1. Separate the clamps. 2. Inspect cables for wear and replace them if necessary. 3. Have a Sears technician test the battery. 4. Ensure correct connections. 5. Verify the Volt/Amp Selector is set correctly.
Why is the start cycle so short when cranking the engine with my DieHard Battery Charger?
A short start cycle during engine cranking can occur due to several reasons: * Drawing more than 250 amps for longer than 3 seconds. * Not waiting 4 minutes (240 seconds) between cranks. * The charger overheating. * A severely discharged battery. Crank time decreases as current draw increases. If drawing over 250 amps, crank time may be less than 3 seconds. Always wait 4 minutes between crank attempts to allow the thermal protector to reset. Ensure the charger vents are not blocked. For a severely discharged battery, charge for 10-15 minutes at the 20 amp manual rate to assist with cranking.
Why does the ammeter read less than selected charge rate on my DieHard 200.71230?
If the ammeter reads lower than the selected charge rate, it could be due to: * An extension cord that is too long or has too small of a wire gauge. * A weak cell or sulfated plate in the battery. * The battery being only partially discharged. Try using a shorter or heavier gauge extension cord. A sulfated battery may eventually take a normal charge if left connected. If the battery doesn't charge, have it tested by a Sears technician. Continue charging the battery.
What to do if DieHard 200.71230 Battery Charger ammeter shows no reading and the fan isn't working?
If you're not seeing a reading on the ammeter and the fan isn't working, it could be due to a lack of power at the receptacle or a loose AC cord/extension cord. Check the fuse or circuit breaker supplying the AC outlet. Also, check the power cord and extension cord for a loose plug.
Why does the ammeter reading stay high on my DieHard Battery Charger?
If the ammeter reading remains high, it's likely that the battery is severely discharged. Continue charging the battery for an additional two hours. If the problem persists, have the battery inspected by a Sears or other qualified service dealer.
Why is my DieHard 200.71230 Battery Charger making a loud buzzing or humming noise?
A loud buzz is usually caused by transformer laminations vibrating, while a hum may indicate a shorted diode. Continue charging; the buzzing sound is generally not abnormal. However, you can have the charger tested by a Sears technician if you are concerned.
General| Input Voltage | 120V AC |
|---|---|
| LED Indicators | Yes |
| Maintain/Trickle Charge | Yes |
| Microprocessor Controlled | Yes |
| Charging Modes | Automatic, Manual |
| Output Voltage | 6V/12V DC |
| Charging Current | 2A |
| Battery Types Supported | AGM |
| Safety Features | Reverse Polarity Protection, Short Circuit Protection |
California Proposition 65 warning about cancer and reproductive harm.
Warning against using unapproved accessories.
Action to take with a damaged charger cord or plug.
Action for a damaged charger from dropping or impact.
Warning against self-repair and seeking qualified service.
Safety measure before cleaning or maintenance.
Preparedness for battery acid contact.
Personal protective equipment recommendations.
First aid for battery acid exposure.
Prohibition of ignition sources near batteries.
Warning about sparking from metal objects.
Removing jewelry to prevent burns from short circuits.
Repeat of California Proposition 65 warning.
Safety procedure for connecting/disconnecting clips.
Connection procedure for negative-grounded vehicles.
Connection procedure for positive-grounded vehicles.
Safe disconnection procedure.
Safety precaution during final connection.
Safe disconnection procedure when battery is outside the vehicle.
Grounding and AC power cord connection instructions.
Using a chart to determine battery charging time.
Using hydrometer or tester for charge level and time calculation.
Safety prerequisite for maintenance.
