10) Parameter of soft limit function (9 in total)
#374 enable Soft Limit 0 BOOL 1/0 0:Disable, 1:Enable
#375 value X-- Soft Limit -400 BOOL -2000~0
#376 value Y-- Soft Limit -400 BOOL -2000~0
BOOL -2000~0#377 value Z-- Soft Limit -400
#378 value A-- Soft Limit -400 BOOL
BOOL
-2000~0
#379 value X++ Soft Limit 400 0~2000
BOOL 0~2000#380 value Y++ Soft Limit 400
BOOL 0~2000400
BOOL 0~2000400
#381 value Z++ Soft Limit
#382 value A++ Soft Limit
8) Parameter of Probe function (8 in total)
9) Parameter of hard limit function(16 in total)
#68 1 BOOL 1/0
0：disable 1：enable
#69 20 mm 0~200
#70 0 BOOL 1/0 1: High; 0:Low active
#71 0 BOOL 1/0 0: current position; 1:fixed position mode
#72
#73
#74
#75
enable Probe
thickness of tool sensor
level of probe signal
initial tool's position
initial X axis in fixed mode
initial Y axis in fixed mode
initial Z axis in fixed mode
Back off distance after probing
0
0
0
10
mm
mm
mm
mm
0-9999
0-9999
0-9999
0~200
#400 enable X-- limit 1 BOOL 1/0
0：Disable 1：Enable
#401 enable Y-- limit 1 BOOL 1/0
0：Disable 1：Enable
#402 Enable Z-- limit 1 BOOL
BOOL
1/0
1/0
0：Disable 1：Enable
0：Disable 1：Enable
#403 enable A-- limit 1
BOOL 1/0
0：Disable 1：Enable
1
BOOL 1/0
0：Disable 1：Enable
1
BOOL 1/0
0：Disable 1：Enable
1
BOOL 1/0
0：Disable 1：Enable
1
BOOL 1/00
#404 enable X++ limit
#405 enable Y++ limit
#406 enable Z++ limit
#407 enable A++ limit
#408 active level X-- limit 1: High; 0:Low
BOOL 1/00 1: High; 0:Low
BOOL 1/00 1: High; 0:Low
BOOL 1/00 1: High; 0:Low
BOOL 1/00 1: High; 0:Low
BOOL 1/0 1: High; 0:Low
#409 active level Y-- limit
#410 active level Z-- limit
#411 active level A-- limit
#412 active level X++ limit
#413 active level Y++ limit 0
BOOL 1/0 1: High; 0:Low0
BOOL 1/0 1: High; 0:Low0
#414 active level Z++ limit
#415 active level A++ limit
Tools position X coordinate in the
Mach(ine) coordinate system
Tools position Y coordinate in the
Mach(ine) coordinate system
The set value will trigger the limit signal.
The limit values refer to the machine
coordinates, not the work piece coordi-
nate.
The set value will trigger the limit signal.
The limit values refer to the machine
coordinates, not the work piece coordi-
nate.
Height of Z axis before the XY move
under the Mach(ine) coordinate system
Para.
Mark
Parameter definition
Default
value
Parameter
Unit
Parameter
Scope
Notes
Para.
Mark
Parameter definition
Default
value
Parameter
Unit
Parameter
Scope
Notes
Para.
Mark
Parameter definition
Default
value
Parameter
Unit
Parameter
Scope
Notes
Page -37Digtital Dream 4 Axis Motion Controller DDCS V2.1 User’s Manual
To Next Page
Loading...
Need help?
General
