Why entry codes will not activate relay 1 on DKS 1803?
If entry codes are not activating relay 1 on your DKS Intercom System, it is likely that the programmed entry codes are greater than the divide number. Reprogram either the divide number or the entry codes to resolve this.
Why entry codes will not activate relay 2 on DKS 1803?
If entry codes are not activating relay 2 on your DKS Intercom System, it could be because the programmed entry codes are less than or equal to the divide number. To fix this, reprogram the divide number or program the entry codes to be greater than the divide number.
Why does my DKS Intercom System emit a beep every 30 seconds?
If your DKS Intercom System emits a beep every 30 seconds, it indicates that the master code switch is in the ON position.
How to fix unreadable LCD on DKS Intercom System?
If the LCD on your DKS Intercom System (1802, 1803, 1810 units only) is unreadable, try adjusting the contrast.
Why is my DKS Entry phone keypad dead?
A dead keypad on your DKS Entry phone could be due to several reasons: * There might be no power. Check for 16.5 VAC input power. * The keypad might not be properly connected to the circuit board. Ensure the cable on the plug points down when connected to the circuit board. * There could be a 16-volt power shorted to ground.
What to do if my DKS Entry phone system emits a long tone and cancels programming?
If your DKS Entry phone system emits a long tone and cancels programming, it could be due to: * Waiting too long between pushing buttons. Try entering information more quickly. * Forgetting to press * first when programming.
How to fix a buzz or noise on the DKS Entry phone line?
To address a buzz or noise on your DKS Entry phone line: * Disconnect the phone line from the system and check it with a handset. If the line is noisy, the problem lies with the phone line itself, not the entry system. * Check for any shorts to ground behind the circuit board. * Inspect for pinched wires near the door hinge. * Ensure phone wires are twisted. * Verify the proper type of phone wire was used, especially for outdoor or underground applications. * Confirm that all wires, including the speaker and keypad, are isolated from ground. * Make sure the cabinet is properly grounded and that the case ground (CGND terminal 3) is not used as a low voltage common. * Check for excessive voltage drop on the 16 VAC power.
What to do if I cannot get into programming mode on my DKS Entry phone?
If you're having trouble entering programming mode on your DKS Entry phone, consider the following: * Ensure you are entering the correct master code. Start over if necessary. * Enter the information more quickly, as waiting too long between button presses can cause issues. * Verify that the keypad is correctly plugged into the board with the cable pointing down. * Check that the memory chip is installed correctly.
Why does my DKS Entry phone system ring or howl from the speaker?
Ringing or howling from the speaker of your DKS Entry phone system could be due to: * Feedback being improperly adjusted. * The volume being set too high.
What to do if my DKS Entry phone door strike locks on?
If the door strike on your DKS Entry phone locks on, it could be due to: * Excessive voltage-drop on the 16 VAC line. * Using a transformer with too low VA rating. * The relay strike time being programmed too long.
FCC compliance information for digital devices in the US.
Canadian compliance for telecommunications equipment.
General guidelines and steps for installing the telephone entry system.
Instructions for surface mounting 1803, 1810, and 1808 models.
Instructions for semi-flush mounting units using a recess box.
Details for flush mounting units into walls with specific kits.
Specifications for the rough-in box used in flush mounting.
Information on the trim ring for flush mount installations.
Instructions for installing the memory chip into the circuit board.
Guidance on installing an optional postal lock for mail carrier access.
Introduction to wiring and adjustment procedures.
Details on adjusting various settings on the control circuit board.
Visual representation of system wiring connections.
Explanation of the purpose of each terminal on the main board.
Procedures for adjusting speaker, microphone, and other settings.
Overview of programming via keypad and remote telephone.
Basic programming steps including Master Code and system settings.
Procedures for entering and managing phone numbers and directory codes.
Setting up and managing four-digit and five-digit entry codes.
Programming time-based functions like time clock and time zones.
General guidance for guests and residents using the system.
Operations for system administrators, including remote access.
Instructions for switch input, talk time, line sharing, and PBX connection.
List of replaceable parts and their part numbers.
Guide to diagnosing and resolving common system issues.
Descriptions and part numbers for optional accessories.
Tables for recording system programming and resident data.
General| Brand | DKS |
|---|---|
| Model | 1803 |
| Category | Intercom System |
| Language | English |
To Next Page
