How to fix switch 2 input will not activate relay on DKS 1810 Intercom System?
If switch 2 input will not activate the relay on your DKS Intercom System, reprogram switch input 2 to activate the relay.
What to do if my DKS Entry system will not answer when called?
If your DKS Entry system isn't answering when called, check these items: * Ensure the ring pin is installed. * Verify the number of rings to answer isn't set too high; reprogram if needed. * Check for a bad phone line or insufficient ring voltage.
Why relay activates but gate operator will not open on DKS 1810 Intercom System?
If the relay activates but the gate operator does not open on your DKS Intercom System, try the following: * Reprogram the relay strike time for a longer duration. * Check the wiring to the gate operator. * Inspect the gate operator itself.
Why does my DKS Entry phone system emit a beep every 30 seconds?
If your DKS Entry phone system beeps every 30 seconds, it's likely because the master code switch is in the ON position. Turn the master code switch OFF.
What to do if the relay activates but the gate operator will not open on my DKS Entry phone?
If the relay activates but the gate operator doesn't open on your DKS Entry phone, consider these steps: * Re-program the relay strike time for a longer period. * Check the wiring to the gate operator. * Check the gate operator itself.
What to do if rotary dial 9 will not activate relay on my DKS Entry phone?
To solve the issue with rotary dial 9 not activating the relay on your DKS Entry phone, adjust the click sensitivity.
What causes buzz or noise on the phone line with my DKS 1810 Intercom System?
If your DKS Intercom System is emitting a buzz or noise on the phone line, try these checks: 1. Disconnect the phone line from the system and test it with a handset to determine if the noise originates from the phone line itself. 2. Inspect for any shorts to ground behind the circuit board. 3. Check for pinched wires near the door hinge. 4. Look for a 16-volt power or phone line shorted to ground. 5. Ensure that phone wires are twisted and that the correct type of phone wire is used, especially for outdoor or underground applications. 6. Verify that all wires, including the speaker and keypad, are isolated from ground. 7. Confirm that the cabinet is properly grounded and that the case ground (terminal 3) is not used as a low voltage common. 8. Check for excessive voltage drop on t...
What to do if door strike or gate operator holds open on DKS 1810 Intercom System?
If the door strike or gate operator on your DKS Intercom System stays open, it might be because: * The auto relay time zone is enabled. Turn off the auto relay feature or reprogram the time zone. * The system received a hold open command. Call the system and press the tone deactivation number.
Why does the door strike lock on my DKS 1810?
If the door strike on your DKS Intercom System locks on, it could be due to: * Excessive voltage drop on the 16 VAC line. * Using a transformer with too low VA rating. * Relay strike time programmed for too long.
Why does my DKS Intercom System emit a long tone and cancels programming?
If your DKS Intercom System emits a long tone and cancels programming, it may be due to: * Pausing too long between button presses. * Forgetting to press the * key before programming.
Key steps for mounting, connecting, and initial programming of the system.
Guidance on making audio adjustments and testing system functionality.
Details FCC compliance requirements and registration information for the equipment.
Information on Canadian Department of Communications certification and installation guidelines.
Specifications for power transformers required for various DoorKing systems in Canada.
Confirmation of product testing and listing according to U.L. 294 Safety Standard.
Details specific mounting height and reach requirements for wheelchair accessibility.
Step-by-step instructions for opening the cabinet, handling the circuit board, and mounting the unit.
Details on mounting the 1803 and 1810 units directly to a wall or using a post.
Instructions for semi-flush mounting 1803/1810 units using an optional recess-mounting box.
Guidelines for installing flush mount units using specific flush mount kits, not designed for weather exposure.
Details on installing the rough-in box component of the flush mount installation kit.
Instructions for using the trim ring component of the flush mount kit for 1803 and 1810 units.
Details on using the surface mount trim ring for flush style units.
Instructions for surface mounting the 1808 model unit directly or using a mounting post.
Procedure for safely installing the memory chip into the circuit board socket.
Steps for installing an Arrow Postal Lock for mail carrier access, including wiring considerations.
Covers essential wiring practices, grounding requirements, power, and wire specifications.
Details on adjusting contrast, volume, sensitivity, and other parameters on the control board.
Illustrates the wiring connections for the 1862-010 control board, including terminals and components.
Explains the function of each terminal on the main terminal strip, relay 2, and switch 2 inputs.
Covers adjusting speaker volume, microphone volume, feedback, click sensitivity, and display contrast.
Details the function and settings of the master code switch, ring pin, and handset/hands-free pins.
Introduces system programming options via keypad or remote telephone, and general programming notes.
Covers setting the master code, system mode, relay strike times, and open tone settings.
Programs the maximum talk time for calls and sets tone open numbers for relay activation.
Configures switch inputs, dialing format (touch-tone/rotary), ring count, and PBX line access codes.
Sets keypad key functions during calls and configures automatic hang-up behavior.
Sets directory code length and programs 7-digit phone numbers for residents.
Programs area codes and phone numbers for long distance or 10-digit dialing.
Includes deleting all numbers, displaying, and deleting individual phone numbers.
Programs, deletes, and sets divide numbers for four-digit entry codes.
Programs, deletes, and sets divide numbers for five-digit entry codes.
Sets the system's current time and date, and configures automatic relay activation time zones.
Sets time zone restrictions for four-digit and five-digit entry codes.
Programs 'FLASH' entry codes that are valid only on specific days of the month.
Covers guest communication, responding to calls, and using entry codes for access.
Details remote programming, relay activation, and checking relay status for system administrators.
Enables or disables entry code and auto relay time zones remotely via phone.
Explains switch input operations, talk time specifics, and line sharing for multiple systems.
Guides on connecting to PBX systems and configuring for areas requiring 10-digit dialing.
Lists replaceable parts and initial troubleshooting steps before contacting support.
Provides solutions for common system symptoms like non-responsiveness, noise, and relay failures.
Lists available accessories and additional troubleshooting tips for entry code and system behavior issues.
Provides tables to record system configuration data such as master codes, entry codes, and time zones.
A template for logging resident information including names, phone numbers, and access codes.
Continuation of the resident data log sheet for comprehensive record-keeping.
Instructions for guests on how to communicate with residents and gain access.
Guidance for residents on privacy settings and using access codes.
General| Brand | DKS |
|---|---|
| Model | 1810 |
| Category | Intercom System |
| Language | English |
To Next Page
