What to do if the keypad is dead on my DKS 1810 Intercom System?
If the keypad on your DKS Intercom System is not working, check the following: * Ensure that the system has 16 VAC input power. * Verify that the keypad is correctly connected to the circuit board, ensuring the cable on the plug points down.
Why does my DKS Intercom System emit a long tone and cancels programming?
If your DKS Intercom System emits a long tone and cancels programming, it may be due to: * Pausing too long between button presses. * Forgetting to press the * key before programming.
Why does the door strike lock on my DKS 1810?
If the door strike on your DKS Intercom System locks on, it could be due to: * Excessive voltage drop on the 16 VAC line. * Using a transformer with too low VA rating. * Relay strike time programmed for too long.
What to do if door strike or gate operator holds open on DKS 1810 Intercom System?
If the door strike or gate operator on your DKS Intercom System stays open, it might be because: * The auto relay time zone is enabled. Turn off the auto relay feature or reprogram the time zone. * The system received a hold open command. Call the system and press the tone deactivation number.
Why is my DKS 1810 Intercom System ringing or howling from the speaker?
If your DKS Intercom System is ringing or howling from the speaker, it may be due to: * Improperly adjusted feedback. * The volume being set too high.
What to do if entry system will not answer when called on DKS Intercom System?
If your DKS Intercom System will not answer when called, check the following: * Ensure that the ring pin is installed. * Verify that the number of rings to answer is not set too high; reprogram if necessary. * Check for a bad phone line or insufficient ring voltage.
How to fix rotary dial 9 not activating relay on DKS 1810?
If rotary dial 9 will not activate the relay on your DKS Intercom System, try adjusting the click sensitivity.
What to do if touch-tone 9 will not activate relay on DKS Intercom System?
If touch-tone 9 is not activating the relay on your DKS Intercom System, consider the following: * Reprogram the tone-open number to 9. * If the resident phone emits a short pulse instead of a long tone, press 9 twice in rapid succession (99). * Try using another phone that is known to work. * Lower the speaker volume and readjust the feedback.
Why relay activates but gate operator will not open on DKS 1810 Intercom System?
If the relay activates but the gate operator does not open on your DKS Intercom System, try the following: * Reprogram the relay strike time for a longer duration. * Check the wiring to the gate operator. * Inspect the gate operator itself.
Why is there a dial tone on the speaker after dial out on my DKS 1810 Intercom System?
If you hear a dial tone on the speaker after dialing out using your DKS Intercom System, it indicates that the phone line is set up for rotary-dial. Contact your phone company and request a switch to a touch-tone line.
Key steps for mounting, connecting, and initial programming of the system.
Guidance on making audio adjustments and testing system functionality.
Details FCC compliance requirements and registration information for the equipment.
Information on Canadian Department of Communications certification and installation guidelines.
Specifications for power transformers required for various DoorKing systems in Canada.
Confirmation of product testing and listing according to U.L. 294 Safety Standard.
Details specific mounting height and reach requirements for wheelchair accessibility.
Step-by-step instructions for opening the cabinet, handling the circuit board, and mounting the unit.
Details on mounting the 1803 and 1810 units directly to a wall or using a post.
Instructions for semi-flush mounting 1803/1810 units using an optional recess-mounting box.
Guidelines for installing flush mount units using specific flush mount kits, not designed for weather exposure.
Details on installing the rough-in box component of the flush mount installation kit.
Instructions for using the trim ring component of the flush mount kit for 1803 and 1810 units.
Details on using the surface mount trim ring for flush style units.
Instructions for surface mounting the 1808 model unit directly or using a mounting post.
Procedure for safely installing the memory chip into the circuit board socket.
Steps for installing an Arrow Postal Lock for mail carrier access, including wiring considerations.
Covers essential wiring practices, grounding requirements, power, and wire specifications.
Details on adjusting contrast, volume, sensitivity, and other parameters on the control board.
Illustrates the wiring connections for the 1862-010 control board, including terminals and components.
Explains the function of each terminal on the main terminal strip, relay 2, and switch 2 inputs.
Covers adjusting speaker volume, microphone volume, feedback, click sensitivity, and display contrast.
Details the function and settings of the master code switch, ring pin, and handset/hands-free pins.
Introduces system programming options via keypad or remote telephone, and general programming notes.
Covers setting the master code, system mode, relay strike times, and open tone settings.
Programs the maximum talk time for calls and sets tone open numbers for relay activation.
Configures switch inputs, dialing format (touch-tone/rotary), ring count, and PBX line access codes.
Sets keypad key functions during calls and configures automatic hang-up behavior.
Sets directory code length and programs 7-digit phone numbers for residents.
Programs area codes and phone numbers for long distance or 10-digit dialing.
Includes deleting all numbers, displaying, and deleting individual phone numbers.
Programs, deletes, and sets divide numbers for four-digit entry codes.
Programs, deletes, and sets divide numbers for five-digit entry codes.
Sets the system's current time and date, and configures automatic relay activation time zones.
Sets time zone restrictions for four-digit and five-digit entry codes.
Programs 'FLASH' entry codes that are valid only on specific days of the month.
Covers guest communication, responding to calls, and using entry codes for access.
Details remote programming, relay activation, and checking relay status for system administrators.
Enables or disables entry code and auto relay time zones remotely via phone.
Explains switch input operations, talk time specifics, and line sharing for multiple systems.
Guides on connecting to PBX systems and configuring for areas requiring 10-digit dialing.
Lists replaceable parts and initial troubleshooting steps before contacting support.
Provides solutions for common system symptoms like non-responsiveness, noise, and relay failures.
Lists available accessories and additional troubleshooting tips for entry code and system behavior issues.
Provides tables to record system configuration data such as master codes, entry codes, and time zones.
A template for logging resident information including names, phone numbers, and access codes.
Continuation of the resident data log sheet for comprehensive record-keeping.
Instructions for guests on how to communicate with residents and gain access.
Guidance for residents on privacy settings and using access codes.
General| Brand | DKS |
|---|---|
| Model | 1810 |
| Category | Intercom System |
| Language | English |
To Next Page
